The total repair cost will vary based on the condition of your vehicle and the number of repairs needed to fix your symptom. Proper diagnosis will save you money by finding the exact repairs needed to fix your car right the first time.
A faulty oxygen sensor is one of the most common causes of a check engine light. Symptoms may include a decrease in fuel mileage, hesitation or misfiring from the engine, rough idling or even stalling. A faulty sensor may cause the vehicle to fail an emissions test.
Any time there is an emissions fault the check engine light will be displayed. The purpose of the check engine light is to inform the driver that an emission related fault has been found, and that there are on-board diagnostic (OBD) trouble codes stored in the powertrain or engine control module. Additionally, since the emissions systems are so intertwined into engine control and transmission control systems, symptoms may include nearly any sort of drivability concerns. This may include harsh shifting, failure to shift, hesitation on acceleration, jerking, engine failure to start or run, loss of power, or any number of other drivability issues.
Due to the nature of electrical systems on modern vehicles, the range of problems these can cause are nearly limitless. However, there is a way to categorize them in two ways. Permanent and intermittent problems. Permanent problems appear and remain. This may be the vehicle will not start, the radio does not work, or the door chime will not turn off among many, many others. These problems are more straight-forward to diagnose since they present themselves at all time. This means there will always be a fault to find. Intermittent electrical problems, however, can be difficult or impossible to locate, since they appear then disappear without warning. The best case scenario for an intermittent issue is when replicating the problem is easily accomplished and understood. This allows a technician to make an issue semi-permanent, allowing them to find the fault. Other issues that come and go without warning and cannot be replicated on demand must occur when the technician is servicing the vehicle, otherwise there is no problem to correct. It is most important to understand that electrical system faults always require inspection, and can include the vehicle working in any manner, or not working at all.
Like we noted in the last section, general diagnosis symptoms are the most vague of the bunch. There are several diagnostic spectrums, electrical diagnosis, drivability diagnostics, engine diagnostics, transmission diagnostics, and the list could continue for about 5 or 10 more spectrums of diagnostics. The most important take-away here, is that general diagnostics are diagnostics that have no other spectrum in which they fit, or the problem is unknown. This means that any vehicle left outside of a repair facility with the keys and an authorization to perform diagnosis will be diagnosed under the general diagnosis spectrum.
When the Check Engine Light comes on, you may experience engine performance issues such as poor acceleration, rough idling, or an engine that won't start. In some cases, no abnormal symptoms will be experienced. Other systems like the transmission or ABS can cause the Check Engine Light to illuminate and lights for those systems can come on at the same time. Similar lights may say "Check Engine Soon", "Malfunction Indicator Light" or just "Check". In rare case the engine can overheat.
When the check engine light comes on in your 2016 Hyundai Azera, it is essential to recognize the urgency of the situation. This warning light acts as an early alert system, indicating that something may be amiss under the hood. Ignoring it can lead to more severe issues, such as engine damage or decreased vehicle performance, which can result in costly repairs. A flashing check engine light is particularly concerning, as it signals a serious problem that could jeopardize your engine's integrity if you continue to drive. Common issues that trigger this light include malfunctioning oxygen sensors, faulty spark plugs, or problems with the catalytic converter, all of which can escalate if not addressed promptly. For DIY enthusiasts, it’s crucial to not only reset the light but also to diagnose and fix the underlying problem to prevent future complications. Taking immediate action not only ensures your vehicle runs smoothly but also safeguards your investment in the long run.
When faced with a check engine light on your 2016 Hyundai Azera, the first step is to check the gas cap, as a loose or damaged cap is a common and easily fixable issue that can trigger the light. If the gas cap is secure, proceed to inspect the air intake system, which may reveal problems related to error codes like p0106. Utilizing a diagnostic tool to read the trouble codes is crucial; this involves connecting a scanner to the OBD2 port, allowing you to pinpoint specific issues. If sensor malfunctions are indicated, addressing these promptly can prevent further complications. Additionally, be aware of common causes such as a dirty mass airflow sensor, vacuum leaks, or catalytic converter issues, which are prevalent in Hyundai vehicles. Finally, if these steps do not resolve the problem, consider taking your Azera to a dealership for a comprehensive engine diagnostic, ensuring that any underlying issues are identified and addressed before they escalate. By following these steps, you can effectively troubleshoot the check engine light and maintain your vehicle's performance.
Read about related problems experienced by other Hyundai Azera drivers like you.
See what others are asking about their Hyundai Azera. Get answers from RepairPal's community of auto experts and enthusiasts.
