The total repair cost will vary based on the condition of your vehicle and the number of repairs needed to fix your symptom. Proper diagnosis will save you money by finding the exact repairs needed to fix your car right the first time.
When the throttle position sensor fails, the engine's computer tends to overcompensate with fuel, leading black exhaust coming from the tailpipe. There is a strong possibility of engine misfires, and the check engine light will come on.
Throttle position sensors can also develop "dead spots," or certain places along the throttle curve where it doesn't get a reading. When this happens, the above symptoms can occur but then stop when you further press or let off the gas pedal.
When the vehicle speed sensor fails or the wiring harness prevents signal transmission, the speedometer is the first thing that will stop functioning properly. This can be an intermittent issue where the speedometer only works occasionally, the speedometer may cease all function, or the speedometer may read erratically or incorrectly. Also, the traction control and anti lock brake warning lights specific to each vehicle may be illuminated, depending on the design of those systems. You may notice the vehicle hesitate to accelerate, cruise control will not function properly, and the vehicle may not shift properly through all of the gears.
In the event that a wheel speed sensor fails, the ABS, traction control system (TCS) and manufacturer specific stability control system lights will illuminate, informing the driver that the systems are disabled. The vehicle will be more prone to tire slip, and normal driving patterns may need to be adjusted to correct for the loss of computer control. On older vehicle's, the speedometer can be affected, causing illumination of the check engine light as well.
The cruise control switch can cause complete failure of the cruise control feature, but in a lucky scenario only partial functionality will be lost. This means that the cruise control may come on, but that it will not increase in speed automatically, or the cancel button does not work leading the driver to cancel cruise control with the foot brake. In some vehicles, the cruise control light may illuminate, or a warning message may be displayed due to lack of functionality.
A faulty cruise control module will simply result in deactivation of cruise control settings. This is because a detected error in the cruise control system could lead to hazardous driving conditions, so the module will be disabled, and the cruise control system warning light will be displayed. This will be a different message depending on make and model, and a warning light or message may be displayed on the driver instrument cluster.
To effectively diagnose a non-functioning cruise control in a 2000 Chrysler Concorde, start with the simplest checks to avoid unnecessary complications. Begin by inspecting the fuses related to the cruise control system, as a blown fuse can often be the culprit behind the malfunction. Next, evaluate the condition of the brake pedal and throttle body, since any issues here can directly impact cruise control functionality. It's essential to refer to your vehicle's manual to locate the fuse box in the engine bay; once found, remove the cruise control fuse for a thorough inspection. Additionally, using a scan tool to check for any stored fault codes can provide valuable insights into the problem. Opt for a higher-end scan tool that can display the cruise control switch states, as this will help you pinpoint whether the issue lies within the switch itself or elsewhere in the system. By following these initial steps, you can systematically narrow down the potential causes of the cruise control failure, making your DIY troubleshooting more efficient.
When dealing with a malfunctioning cruise control system in a 2000 Chrysler Concorde, it's essential to understand the common problems that could be at play. One of the primary culprits is a faulty cruise control switch, which can prevent the system from engaging properly. Additionally, a blown fuse may disrupt the electrical flow necessary for the cruise control to function, making it a straightforward issue to check and replace. Another potential issue is vacuum leaks within the cruise control system, which can lead to a loss of functionality and require careful inspection of the vacuum lines. The speed sensor is also critical; if it is defective, the cruise control may struggle to maintain a set speed. Furthermore, problems with the brake light switch can interfere with the system's ability to engage, as the cruise control is designed to deactivate when the brakes are applied. Lastly, a malfunctioning throttle cable can impact the overall operation of the cruise control system. By understanding these common issues, DIYers can better diagnose the problem and take the necessary steps to restore their vehicle's cruise control functionality.
When it comes to a non-functioning cruise control in a 2000 Chrysler Concorde, the urgency to address the issue should not be underestimated. While it may not present an immediate safety hazard, neglecting this problem can lead to a less enjoyable driving experience, particularly on long trips where cruise control is most beneficial. A malfunctioning system may also signal deeper electrical issues within the vehicle, which could escalate if left unchecked. Furthermore, ignoring the cruise control problem could result in more extensive damage over time, ultimately leading to higher repair costs. For DIY enthusiasts, it’s crucial to recognize that timely diagnosis and repair not only restore the convenience of cruise control but also contribute to the overall health of the vehicle. Therefore, while it may not be an emergency, addressing the malfunction promptly is a wise decision that enhances both safety and driving comfort.
Read about related problems experienced by other Chrysler Concorde drivers like you.
See what others are asking about their Chrysler Concorde. Get answers from RepairPal's community of auto experts and enthusiasts.