2010 Toyota Tacoma Tire Pressure Light Won't Go Off (TPMS)

Resolve the persistent TPMS light in your 2010 Toyota Tacoma.

Find Repair Location
Reviewed by
Aisha
Written by RepairPal Car Genius
Updated January 14, 2025
0%
40% chance it's the
Tire Leaking Air
0%
30% chance it's the
Wheel Leaking Air
0%
15% chance it's the
Tire Pressure Monitoring System
0%
15% chance it's
Something else
The most common reasons a 2010 Toyota Tacoma tire pressure warning light stays on are a leaking tire, a wheel that no longer holds air, or a faulty tire pressure monitoring system.
  • Tire Leaking Air: A puncture, valve stem issue, or rim damage can cause a tire to leak air, leading to loss of pressure.
  • Wheel Leaking Air: A puncture or damage to the tire or rim can cause air to leak, resulting in a loss of tire pressure.
  • Tire Pressure Monitoring System: A malfunctioning tire pressure monitoring system can be caused by faulty sensors or a dead battery in the sensor units.
Proper diagnosis will determine the exact cause of your symptom, saving you money on unnecessary repairs. The diagnostic experts at RepairPal Certified shops have the right tools and experience to solve any symptom.

How much does it cost to fix a 2010 Toyota Tacoma tire pressure warning light stays on?

Common Repairs

The total repair cost will vary based on the condition of your vehicle and the number of repairs needed to fix your symptom. Proper diagnosis will save you money by finding the exact repairs needed to fix your car right the first time.

When a tire pressure monitoring sensor fails, the tire pressure monitoring system control module will recognize a loss in communication and turn on the warning lamp which indicates the failure. This is most often the case. However, the tire pressure monitoring sensor may also fail by reporting incorrect tire pressures. This could cause a flat tire to go unrecognized, or a properly inflated tire to signal a low or high tire pressure warning.

When a relearn is needed, for any reason, the TPMS warning light will illuminate, and many vehicles will display a message relating to the TPMS system being inoperative or loosing communication. It is important to keep a watchful eye on tire pressures when this system is having issues because there is no warning available for underinflation or overinflation of the tires.

Wheels offer very few symptoms, but these symptoms should never be ignored. Visible cracks on the wheels may appear, especially after hitting a large bump, Most often, this will also be accompanied by loss of air from the tire on that wheel. Also, vibration in the steering wheel is very common when the tire is out of balance, and improper wheel nuts or bolts can cause creaking and popping noises to develop. Again, there are very few symptoms, but they should not be ignored.

The only symptoms of a TPMS control module failure are failing to alert the driver of underinflation or overinflation of one or more tires, failure to communicate with the body control module or TPMS sensors, or erroneously reporting incorrect tire pressure.

The only symptoms requiring diagnosis for the tire pressure monitoring system warning lamp is if the warning lamp has illuminated while the tires have correct air pressure, or if the air pressure for the tires is out of specification and the warning lamp is off. This is because the overwhelming majority of cases where the TPMS lamp illuminates is due to the change in ambient temperature.

What steps should I take to diagnose the tire pressure light issue on my 2010 Toyota Tacoma?

To effectively diagnose the tire pressure warning light issue on your 2010 Toyota Tacoma, start with the simplest solutions before progressing to more complex diagnostics. Begin by checking the tire pressure of all tires, including the spare, ensuring they are inflated to the recommended levels specified on the tire information placard or in the owner's manual. If the tire pressures are correct, proceed to reset the Tire Pressure Monitoring System (TPMS) by turning the ignition to the ON position and locating the TPMS reset button, typically found under the dashboard. Press and hold this button until the warning light blinks three times, indicating the system is in learn mode. After releasing the button, start the engine and drive at a speed of at least 25 mph for about 10 minutes to allow the system to relearn the sensor values. If the warning light remains illuminated or continues to blink, it may indicate a faulty TPMS sensor, which could include issues with the spare tire sensor. In cases where tires have been rotated or replaced, the sensors may need to be relearned, either through the reset method or with a TPMS tool. If these steps do not resolve the issue, consider using specialized tools like Toyota Techstream or an Autel TPMS tool to register sensor IDs, especially if aftermarket wheels or cloned sensors are involved. Lastly, if the warning light persists despite correct tire pressure and successful resets, there may be a malfunction within the TPMS system, necessitating further diagnosis from a mechanic or tire shop. By following this structured approach, you can effectively troubleshoot and address the tire pressure warning light issue on your Tacoma.

What could cause the tire pressure light to remain on in a 2010 Toyota Tacoma?

When the tire pressure light stays on in your 2010 Toyota Tacoma, it can be frustrating, especially after you've checked the tire pressure. One common issue is under-inflated tires; even minor discrepancies in pressure can trigger the light, so it's essential to verify that all tires, including the spare, are inflated to the manufacturer's recommended levels. Additionally, consider the age of your TPMS sensors, as they typically have a battery life of around ten years. If your vehicle's sensors are older, they may be experiencing battery failure, which can prevent the system from functioning correctly. Another possibility is that one or more TPMS sensors are faulty; a blinking light at startup that turns solid can indicate this problem. Don't forget to check the spare tire as well, as it may also have a sensor that needs attention. In some cases, the issue could lie with the TPMS module itself, although this is less common. Lastly, if all else seems fine, the system may simply need a reset, which can often be done through a button in the glove compartment or by following the reset procedure in your owner's manual. If you're still unsure, consulting a professional mechanic or a tire shop for a sensor test can provide clarity and ensure your vehicle is safe to drive.

What should I do if the tire pressure light on my 2010 Toyota Tacoma won't turn off?

If the tire pressure light on your 2010 Toyota Tacoma remains illuminated, it’s crucial to address the issue without delay. Ignoring this warning can lead to unsafe driving conditions, such as reduced traction and increased tire wear, which may ultimately result in a blowout or loss of control while driving. Start by checking the tire pressure of all tires, including the spare, to ensure they are inflated to the recommended levels. If the pressure is correct but the light persists, consider resetting the Tire Pressure Monitoring System (TPMS) to recalibrate the sensors. Additionally, inspect the spare tire and its sensor, as a malfunctioning spare can also trigger the warning light. If you suspect a sensor issue, it’s advisable to have them checked at a tire shop, as faulty sensors can compromise your vehicle's safety. For a temporary fix, some DIY enthusiasts may choose to disable the TPMS light, but this should not be a long-term solution. Ultimately, addressing the tire pressure light promptly not only ensures your safety but also helps maintain the longevity and performance of your Tacoma.

You’ve got options with RepairPal

Whether you need a more accurate auto repair estimate or help finding a reputable shop in your area, we’ve got you covered.