The total repair cost will vary based on the condition of your vehicle and the number of repairs needed to fix your symptom. Proper diagnosis will save you money by finding the exact repairs needed to fix your car right the first time.
A faulty oxygen sensor is one of the most common causes of a check engine light. Symptoms may include a decrease in fuel mileage, hesitation or misfiring from the engine, rough idling or even stalling. A faulty sensor may cause the vehicle to fail an emissions test.
Any time there is an emissions fault the check engine light will be displayed. The purpose of the check engine light is to inform the driver that an emission related fault has been found, and that there are on-board diagnostic (OBD) trouble codes stored in the powertrain or engine control module. Additionally, since the emissions systems are so intertwined into engine control and transmission control systems, symptoms may include nearly any sort of drivability concerns. This may include harsh shifting, failure to shift, hesitation on acceleration, jerking, engine failure to start or run, loss of power, or any number of other drivability issues.
Due to the nature of electrical systems on modern vehicles, the range of problems these can cause are nearly limitless. However, there is a way to categorize them in two ways. Permanent and intermittent problems. Permanent problems appear and remain. This may be the vehicle will not start, the radio does not work, or the door chime will not turn off among many, many others. These problems are more straight-forward to diagnose since they present themselves at all time. This means there will always be a fault to find. Intermittent electrical problems, however, can be difficult or impossible to locate, since they appear then disappear without warning. The best case scenario for an intermittent issue is when replicating the problem is easily accomplished and understood. This allows a technician to make an issue semi-permanent, allowing them to find the fault. Other issues that come and go without warning and cannot be replicated on demand must occur when the technician is servicing the vehicle, otherwise there is no problem to correct. It is most important to understand that electrical system faults always require inspection, and can include the vehicle working in any manner, or not working at all.
Like we noted in the last section, general diagnosis symptoms are the most vague of the bunch. There are several diagnostic spectrums, electrical diagnosis, drivability diagnostics, engine diagnostics, transmission diagnostics, and the list could continue for about 5 or 10 more spectrums of diagnostics. The most important take-away here, is that general diagnostics are diagnostics that have no other spectrum in which they fit, or the problem is unknown. This means that any vehicle left outside of a repair facility with the keys and an authorization to perform diagnosis will be diagnosed under the general diagnosis spectrum.
When the Check Engine Light comes on, you may experience engine performance issues such as poor acceleration, rough idling, or an engine that won't start. In some cases, no abnormal symptoms will be experienced. Other systems like the transmission or ABS can cause the Check Engine Light to illuminate and lights for those systems can come on at the same time. Similar lights may say "Check Engine Soon", "Malfunction Indicator Light" or just "Check". In rare case the engine can overheat.
When faced with a check engine light on your 2011 Mitsubishi Eclipse, it's essential to approach the diagnosis methodically, starting with the simplest solutions. Begin by checking the gas cap; a loose or damaged cap is a frequent culprit that can trigger the light. Next, take a moment to inspect your dashboard gauges for any additional warning lights or irregular readings that might indicate other underlying issues. Utilizing an OBD-II scanner is a crucial step in this process, as it allows you to retrieve specific error codes that can direct you to the exact problem. Additionally, ensure that all essential fluid levels—such as oil, coolant, and transmission fluid—are adequate, as low levels can also cause the check engine light to activate. Don't overlook the importance of inspecting the wiring and connections under the hood for any visible damage or corrosion, which could lead to electrical issues. Finally, consulting your owner's manual can provide tailored insights into what the check engine light may signify for your specific model. By following these steps, you can effectively narrow down the potential causes of the check engine light and take informed action towards resolving the issue.
When the check engine light comes on in a 2011 Mitsubishi Eclipse, it can be a source of concern for any DIY car owner. One of the most straightforward issues to check is the gas cap; a loose or damaged cap can easily trigger the light, so ensuring it is secure is a good first step. If the gas cap is not the culprit, the oxygen sensor may be at fault, as a malfunction here can lead to poor fuel efficiency and emissions problems. Another common issue is the catalytic converter, which can fail or become inefficient, causing the light to illuminate. Additionally, problems with spark plugs or ignition coils can lead to engine misfires, while a faulty mass airflow sensor can disrupt the air-fuel mixture, both of which will trigger the check engine light. Lastly, don’t overlook the exhaust gas recirculation (EGR) system; a clogged valve can also be a reason for the warning light. While some of these issues can be diagnosed and addressed at home, it’s always wise to consult a qualified mechanic for a thorough diagnosis if the light persists.
When the check engine light illuminates in your 2011 Mitsubishi Eclipse, it signals a potential issue that requires immediate attention. Ignoring this warning can lead to a cascade of problems, including decreased engine performance, reduced fuel efficiency, and even severe engine damage over time. For DIY enthusiasts, the first step is to use an OBD-II scanner to retrieve diagnostic trouble codes (DTCs) that can pinpoint the issue. This initial diagnosis can help you determine whether the problem is something manageable, like a loose gas cap, or more complex, such as a failing sensor or catalytic converter. Addressing these issues promptly not only saves you from costly repairs down the line but also ensures your vehicle remains safe and reliable on the road. Therefore, taking action as soon as the check engine light appears is crucial for maintaining the health of your Mitsubishi Eclipse and preventing further complications.
Read about related problems experienced by other Mitsubishi Eclipse drivers like you.
See what others are asking about their Mitsubishi Eclipse. Get answers from RepairPal's community of auto experts and enthusiasts.
