The total repair cost will vary based on the condition of your vehicle and the number of repairs needed to fix your symptom. Proper diagnosis will save you money by finding the exact repairs needed to fix your car right the first time.
A faulty oxygen sensor is one of the most common causes of a check engine light. Symptoms may include a decrease in fuel mileage, hesitation or misfiring from the engine, rough idling or even stalling. A faulty sensor may cause the vehicle to fail an emissions test.
Any time there is an emissions fault the check engine light will be displayed. The purpose of the check engine light is to inform the driver that an emission related fault has been found, and that there are on-board diagnostic (OBD) trouble codes stored in the powertrain or engine control module. Additionally, since the emissions systems are so intertwined into engine control and transmission control systems, symptoms may include nearly any sort of drivability concerns. This may include harsh shifting, failure to shift, hesitation on acceleration, jerking, engine failure to start or run, loss of power, or any number of other drivability issues.
Due to the nature of electrical systems on modern vehicles, the range of problems these can cause are nearly limitless. However, there is a way to categorize them in two ways. Permanent and intermittent problems. Permanent problems appear and remain. This may be the vehicle will not start, the radio does not work, or the door chime will not turn off among many, many others. These problems are more straight-forward to diagnose since they present themselves at all time. This means there will always be a fault to find. Intermittent electrical problems, however, can be difficult or impossible to locate, since they appear then disappear without warning. The best case scenario for an intermittent issue is when replicating the problem is easily accomplished and understood. This allows a technician to make an issue semi-permanent, allowing them to find the fault. Other issues that come and go without warning and cannot be replicated on demand must occur when the technician is servicing the vehicle, otherwise there is no problem to correct. It is most important to understand that electrical system faults always require inspection, and can include the vehicle working in any manner, or not working at all.
Like we noted in the last section, general diagnosis symptoms are the most vague of the bunch. There are several diagnostic spectrums, electrical diagnosis, drivability diagnostics, engine diagnostics, transmission diagnostics, and the list could continue for about 5 or 10 more spectrums of diagnostics. The most important take-away here, is that general diagnostics are diagnostics that have no other spectrum in which they fit, or the problem is unknown. This means that any vehicle left outside of a repair facility with the keys and an authorization to perform diagnosis will be diagnosed under the general diagnosis spectrum.
When the Check Engine Light comes on, you may experience engine performance issues such as poor acceleration, rough idling, or an engine that won't start. In some cases, no abnormal symptoms will be experienced. Other systems like the transmission or ABS can cause the Check Engine Light to illuminate and lights for those systems can come on at the same time. Similar lights may say "Check Engine Soon", "Malfunction Indicator Light" or just "Check". In rare case the engine can overheat.
When faced with a check engine light on your 2017 Dodge Charger, it's essential to adopt a methodical diagnostic approach to efficiently identify the underlying issue. Start by checking the gas cap; a loose or damaged cap is a common culprit that can easily trigger the light. Next, take a moment to inspect your dashboard for any additional warning lights or messages that might offer further insights into the problem. Utilizing an OBD-II scanner is a crucial step in this process, as it allows you to retrieve specific error codes that can direct you to the exact issue. Additionally, examining the condition of your spark plugs is vital, as worn plugs can lead to engine performance problems. Don't forget to check the levels of essential fluids like oil and coolant, as low levels can also cause the check engine light to activate. Finally, inspect the wiring and connections under the hood for any signs of damage or corrosion, as faulty wiring can be a significant factor in triggering the light. By following these steps, you can effectively narrow down the potential causes of the check engine light and take informed actions towards resolving the issue.
When the check engine light illuminates in a 2017 Dodge Charger, it signals potential issues that DIY enthusiasts can troubleshoot. One of the most straightforward problems to check is a loose gas cap, which can disrupt fuel system pressure; simply tightening or replacing the cap can often resolve the issue. Another common cause is a faulty oxygen sensor, which can lead to decreased fuel efficiency and increased emissions; replacing this sensor is a manageable task for those with basic mechanical skills. Additionally, problems with the catalytic converter may trigger the light, indicating a need for inspection or possible replacement if it’s malfunctioning. Spark plug or ignition coil issues are also prevalent, as they can cause engine misfires and performance problems, which can be diagnosed with engine diagnostics tools. The mass airflow sensor can also fail, disrupting the air-fuel mixture and activating the check engine light. Lastly, issues with the exhaust gas recirculation (EGR) system, such as a clogged valve, can contribute to the light's illumination. By addressing these common issues promptly, DIYers can not only turn off the check engine light but also enhance their vehicle's performance and longevity.
When the check engine light illuminates in your 2017 Dodge Charger, it signals a need for immediate attention, as neglecting this warning can lead to serious consequences. The light may indicate a range of issues, from minor sensor malfunctions to significant engine problems that could compromise your vehicle's performance and safety. Ignoring the light not only risks decreased fuel efficiency but can also escalate minor issues into costly repairs, potentially stranding you on the road. For DIY enthusiasts, the first step is to use an OBD-II scanner to retrieve diagnostic trouble codes, which can provide insight into the specific problem. This proactive approach allows you to address issues before they worsen, ensuring your Charger remains reliable and safe. Remember, timely intervention can save you money and prevent further damage, making it crucial to act swiftly when the check engine light appears.
See what others are asking about their Dodge Charger. Get answers from RepairPal's community of auto experts and enthusiasts.
Read about related problems experienced by other Dodge Charger drivers like you.
