The total repair cost will vary based on the condition of your vehicle and the number of repairs needed to fix your symptom. Proper diagnosis will save you money by finding the exact repairs needed to fix your car right the first time.
When a tire pressure monitoring sensor fails, the tire pressure monitoring system control module will recognize a loss in communication and turn on the warning lamp which indicates the failure. This is most often the case. However, the tire pressure monitoring sensor may also fail by reporting incorrect tire pressures. This could cause a flat tire to go unrecognized, or a properly inflated tire to signal a low or high tire pressure warning.
When a relearn is needed, for any reason, the TPMS warning light will illuminate, and many vehicles will display a message relating to the TPMS system being inoperative or loosing communication. It is important to keep a watchful eye on tire pressures when this system is having issues because there is no warning available for underinflation or overinflation of the tires.
Wheels offer very few symptoms, but these symptoms should never be ignored. Visible cracks on the wheels may appear, especially after hitting a large bump, Most often, this will also be accompanied by loss of air from the tire on that wheel. Also, vibration in the steering wheel is very common when the tire is out of balance, and improper wheel nuts or bolts can cause creaking and popping noises to develop. Again, there are very few symptoms, but they should not be ignored.
The only symptoms requiring diagnosis for the tire pressure monitoring system warning lamp is if the warning lamp has illuminated while the tires have correct air pressure, or if the air pressure for the tires is out of specification and the warning lamp is off. This is because the overwhelming majority of cases where the TPMS lamp illuminates is due to the change in ambient temperature.
To effectively diagnose the tire pressure light issue on your 2014 Toyota Highlander, start by checking the tire pressure of all tires, including the spare, ensuring they are inflated to the recommended levels specified in your owner's manual or on the tire information placard. Next, inspect each tire for visible damage or leaks, as any punctures can trigger the warning light. If the tire pressure is correct and the tires are in good condition, proceed to reset the Tire Pressure Monitoring System (TPMS) by locating the "SET" or "TPMS RESET" button, turning the ignition to the "ON" position without starting the engine, and holding the button until the dashboard light blinks. After releasing the button, drive the vehicle at a speed of at least 25 mph to allow the system to recalibrate. Don’t forget to check the spare tire as well, as an improperly inflated spare can also affect the TPMS. If the light persists, consider using a TPMS scan tool to diagnose any sensor issues. Finally, if these steps do not resolve the problem, consult your owner's manual for further guidance or seek assistance from a qualified mechanic. This systematic approach will help you efficiently identify and address the tire pressure light issue.
When the tire pressure light remains illuminated in your 2014 Toyota Highlander, it often points to several common issues that can be addressed through DIY methods. One of the primary culprits is low tire pressure, which can affect any of the tires, including the spare. To resolve this, check the pressure of all tires and inflate them to the recommended levels specified on the tire information placard located on the driver's side doorjamb. If the tire pressures are adequate, the next step is to reset the Tire Pressure Monitoring System (TPMS). This can typically be done by locating the reset button under the dashboard, turning the ignition to the "ON" position without starting the engine, and holding the button until the warning light flashes or turns off. Additionally, if the light blinks and then stays on, it may indicate a malfunction with the tire pressure sensors, which could be due to a dead battery or a connection issue. Don’t forget to check the spare tire as well, since its pressure can also trigger the warning light. If these steps do not resolve the issue, it may be necessary to use an OBD2 scanner to diagnose potential system failures. By systematically checking these factors, you can effectively troubleshoot and potentially fix the tire pressure light issue in your Highlander.
When the tire pressure light illuminates in your 2014 Toyota Highlander, it is crucial to act promptly to ensure your safety and the longevity of your tires. Ignoring this warning can lead to serious consequences, such as tire blowouts or decreased vehicle handling, which can compromise your safety on the road. Start by checking the tire pressure in all four tires, as maintaining the correct pressure is essential for optimal performance and safety. If the pressure is low, inflate the tires to the recommended levels found on the driver’s door jamb or in the owner’s manual. Next, visually inspect each tire for any signs of damage or flats, as a compromised tire can exacerbate the issue. If everything appears normal, proceed to reset the Tire Pressure Monitoring System (TPMS) to ensure it accurately reflects the current tire conditions. However, if the light remains on after these steps, it may indicate a deeper issue within the TPMS system itself, necessitating the use of a scanner to identify any error codes. Remember, driving with the TPMS light on without addressing the underlying issue can lead to further complications, so it’s best to consult a mechanic if the problem persists. Taking these immediate steps not only enhances your safety but also helps prevent costly repairs down the line.
See what others are asking about their Toyota Highlander. Get answers from RepairPal's community of auto experts and enthusiasts.
Read about related problems experienced by other Toyota Highlander drivers like you.