Learn About Your Car

Are you interested in certification?

Schedule a Demo

Knock Sensor Replacement

What is a knock sensor?

The engine knock sensor alerts the driver that knocking has been detected inside the engine.

How does the knock sensor work?

Every time the engine knock sensor notices a vibration, it sends a signal to the engine's computer, reporting how large it was. The engine's computer is programmed to expect a specified range of signals from the knock sensor. Most information from the knock sensor will be bumps in the road or closing the car door. However, when a vibration is large enough, the knock sensor signal will trigger the computer to alert the driver. This is a protective measure meant to prevent complete engine failure.

When a knock sensor fails, the engine may lack power, have poor acceleration, ping or knock on acceleration, and get poor fuel economy.

The Check Engine Light may illuminate with a fault code set for one or more knock sensors.

Mitsubishi Knock Sensor Replacement Cost Estimates

The average cost for a Knock Sensor Replacement is between $512 and $713 but can vary from car to car.

Mitsubishi Outlander Sport

Mitsubishi Diamante Knock Sensor Replacement Cost by Year

The average cost for a Mitsubishi Diamante Knock Sensor Replacement is between $512 and $713 but can vary from car to car.

2004 Mitsubishi Diamante

$512-$713

2003 Mitsubishi Diamante

$512-$713

2002 Mitsubishi Diamante

$512-$713

2001 Mitsubishi Diamante

$512-$713

2000 Mitsubishi Diamante

$512-$713

1999 Mitsubishi Diamante

$512-$713

1998 Mitsubishi Diamante

$512-$713

1997 Mitsubishi Diamante

$512-$713

1996 Mitsubishi Diamante

$350-$458

1995 Mitsubishi Diamante

$414-$570

1994 Mitsubishi Diamante

$350-$458

1993 Mitsubishi Diamante

$350-$458

1992 Mitsubishi Diamante

$350-$458

Show All Years

More RepairPal Resources

Knock Sensor Replacement

Jump to:Commonly associated repairs Related OBD codes Cost estimates by vehicle Cost estimates by year

What is a knock sensor?

The engine knock sensor alerts the driver that knocking has been detected inside the engine.

How does the knock sensor work?

When a knock sensor fails, the engine may lack power, have poor acceleration, ping or knock on acceleration, and get poor fuel economy.

The Check Engine Light may illuminate with a fault code set for one or more knock sensors.

Estimates last updated June 18, 2026

1998 Mitsubishi Diamante Knock Sensor Replacement Cost

The average cost for a 1998 Mitsubishi Diamante Knock Sensor Replacement is between $512 and $713.

Labor costs are estimated between $329 and $483 while parts are priced between $182 and $230.
This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.
For a more accurate estimate based on your location, use our Fair Price Estimator below.

What are the symptoms related to a bad knock sensor?

When the knock sensor sends a warning signal to the vehicle's computer, the computer will usually reduce power output and illuminate the check engine light. Some vehicles will not restart until the problem has been fixed. » MORE: How to tell if you have a bad knock sensor

Can I drive with a knock sensor problem?

No. When the knock sensor sends a warning to the computer, it is always treated as if there is an internal engine failure. The vehicle should not be started or driven until the knock sensor is diagnosed as faulty, or the issue is repaired.

How often do knock sensors need to be replaced?

On most vehicles, the knock sensor is tough enough to last over 150,000 miles.

How are knock sensor issues diagnosed?

The check engine light and knock sensor-related OBD codes will immediately point a technician to the knock sensor. The technician will first conduct a visual inspection of the sensor and associated wiring. If the knock sensor wiring harness and electrical connectors are working properly, the technician will test the knock sensor. Further bench testing may be done. After testing is complete, the part will be replaced and the car tested to make sure the problem is resolved.

A knock sensor code isn't always triggered by a defective knock sensor. It can be triggered by a malfunctioning EGR system, a lean air-to-fuel ratio, worn ignition components, a cooling system problem, or an engine mechanical problem.

How is a knock sensor replaced?

If the knock sensor is faulty, the technician will unscrew the bad sensor and install a new one. There is normally only one electrical connector per knock sensor, and there may be more than one knock sensor on the engine.

Get a RepairPal Fair Price Estimate® for your 1998 Mitsubishi Diamante.

Our Fair Price Estimate will help you avoid overpaying based on your car, needed service, and labor rates in your area.