Learn About Your Car

Heater Hose Replacement Cost

Estimates last updated January 1, 1970

2008 Chevrolet Suburban 1500 Heater Hose Replacement Cost

The average cost for a 2008 Chevrolet Suburban 1500 Heater Hose Replacement is between $1,804 and $1,923.

Labor costs are estimated between $171 and $251 while parts are priced between $1,633 and $1,672.
This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.
For a more accurate estimate based on your location, use our Fair Price Estimator below.

Heater Hose Replacement

What is a heater hose?

Heater hoses carry engine coolant from the engine to the heater core. There is one inlet hose, and one outlet hose. On older vehicles, the inlet hose may be split into two segments, separated by a heater control valve.

How does the heater hose work?

All engine cooling system hoses work the same way. They are pressed onto a connector at both ends, and either clamped, or sealed with an O-ring type seal. This provides a watertight seal between the two components being connected.

Coolant hoses can be damaged by oil leaks. The issue should be addressed in order to avoid damaging the new hoses.

What are the symptoms related to a bad heater hose?

Need a repair? Trust our RepairPal Certified network.

With thousands of repair shops to choose from, how do you find one that is honest and fair? We've done the research for you.

Chevrolet Heater Hose Replacement Cost Estimates

The average cost for a Heater Hose Replacement is between $1,804 and $1,923 but can vary from car to car.

Chevrolet Silverado 1500

Chevrolet Silverado 2500 HD

Chevrolet Suburban 1500 Heater Hose Replacement Cost by Year

The average cost for a Chevrolet Suburban 1500 Heater Hose Replacement is between $1,804 and $1,923 but can vary from car to car.

2014 Chevrolet Suburban 1500

$1,804-$1,923

2013 Chevrolet Suburban 1500

$1,804-$1,923

2012 Chevrolet Suburban 1500

$1,804-$1,923

2011 Chevrolet Suburban 1500

$1,804-$1,923

2010 Chevrolet Suburban 1500

$1,804-$1,923

More RepairPal Resources

Heater Hose Replacement

Jump to:Commonly associated repairs Cost estimates by vehicle Cost estimates by year

What is a heater hose?

How does the heater hose work?

Coolant hoses can be damaged by oil leaks. The issue should be addressed in order to avoid damaging the new hoses.

What are the symptoms related to a bad heater hose?

A failing heater hose may cause the vehicle to smell of engine coolant under the hood. If coolant runs onto the heater core inlet or outlet, the cabin could begin to smell of coolant and mildew. Also, the engine may being to run increasingly warmer until the vehicle is repaired. Coolant may leak onto the engine, firewall, and ground, as a defective hose may swell and burst. The worst-case scenario is engine overheating, and possible cylinder head gasket failure.

Can I drive with a heater hose problem?

If the heater control valve is leaking, it is not advised to drive the vehicle as overheating can result from any coolant leak. In this situation, towing the vehicle to a repair facility is the best course of action. When the heater control valve is simply unresponsive, it will not affect drivability in any way, but passenger comfort may be negatively affected.

How often do heater hoses need to be replaced?

Hoses are considered “wear and tear” items, and are expected to be replaced at least once over the life of the vehicle. They tend to fail more quickly if the cooling system is not properly maintained according to the manufacturer's’ scheduled maintenance intervals.

How are heater hose issues diagnosed?

Heater hoses must be replaced when, at any position on the hose, there is an engine coolant leak or obvious swelling. Also, replacement will be recommended if the hoses are cracked, or worn down by prolonged contact with warm or vibrating engine components.

How is a heater hose replaced?

The coolant is drained from the engine in preparation for servicing the engine cooling system. Clamps will be removed from the ends of the hoses, and the hose will be removed from the heater core and engine. The inlet and outlet flanges on the heater core and engine are cleaned in preparation for installation of the new hoses.

If the vehicle has a heater control valve attached to the heater hoses, they should all be replaced at the same time.

We recommend using molded coolant hoses rather than "universal" hoses. Universal hoses can be deformed by pressure and heat and are prone to failure earlier than hoses designed to fit your vehicle.