The window glass lift plates tend to bend or break and cause the window glass to tilt and bind in the door. The lift plates can be replaced separately from the window regulator. In more severe cases, however, a new window regulator may also require replacement.
The Window Glass May not Roll Correctly Due to Damaged Glass Lift Plates on Chrysler 300M
Average mileage: 123,696 (12,000–263,500)
40 people reported this problem
17 people shared problem details
The front driver's side window falls forward when I try to open it and you almost need 2 people to get it closed. One to put a hand on each side of the glass to guide it back up to the closed position, and one running the automatic window switch.
1999 Chrysler 300M149,500Visitor
13 years in my 1999 300M and I rolled up my window but it came out of the track.
2000 Chrysler 300M200,000Visitor
Not fixed been replaced once but broke again within six months now just live with it.
2002 Chrysler 300M100,000Visitor
window binds up all the time.replaced the window regulator with a better quality aftermarket. the previous owner had replaced the regulator with a used one inproperly.
1999 Chrysler 300M65,000Visitor
Got new lift Plates
1999 Chrysler 300M98,000Visitor
why if there are so many 300M's out there are only 21 reports on this issue, I can replace them but I think this should have been a safety recall, this will be the third time!!!!
1999 Chrysler 300M160,000Visitor
Not fixed it sucks
my window is off track the metal black things holding it to the track broke
2001 Chrysler 300M120,000Visitor
Well this won't be helpful: door with the bad window was subsequently smashed while parked. Replaced the door.
2004 Chrysler 300M129,944Visitor
windows don't want to go down, abs, brake light, and airbag, light stays on, car over heating, and always had problems with this car since I bought it. had to do transmission, the engine heads, and all kinds of work. called the place where I bought it even sent a letter to Sharon moss, and still no results. I am so tired of putting money in this car and I'm not working, just can't afford this anymore.
1999 Chrysler 300M48,000Visitor
The front driver's side window falls forward when I try to open it and it requires 2 people to get it closed. (One to put a hand on each side of the glass to guide it back up to the closed position, and one running the automatic window switch.)
2000 Chrysler 300M112,000Visitor
2 out of my 4 Windows make noise when going up. They also roll up rather slow and with hesitation.
1999 Chrysler 300M118,000Visitor
Started with a broken window clip in 2005. I took it apart two different times and JB welded the front drivers side window clip and it lasts a year or two. this winter I purchased a new part from Chrysler for $11 and will replace myself it in the spring.
The front driver window glass jumped off the track, December, 2012.
2000 Chrysler 300M263,500Visitor
I had the same problem but i had the sunroof so it didnt really bother me untill the weather started to get cold.. went to LKQ paid $56 got 2 new/used replacements out of a 04 dodge intrepid, only hard part is the door panel... Its a job you can do yourself.. BUT THE CLIPS ARE TO BLAME!!!! They are cheap and break easy so dont be replacing everything untill its verified that other components are the issue... CHECK THE CLIPS!!!
2000 Chrysler 300M132,000Visitor
window lift plate bent and when window is rolled down, it tilts and has to be forced back into position to close. I push outward on it and it usually works back into place, just take it slow so you don't snap the glass.
window has completely stop working and had very little sign of warning.
Hello, I own a used Chrysler 300 M with 133,000 miles on it. It recently started running out on...
looking to replace the fuel pressure regulator due to the car skipping and has a real bad mist....
What are the steps that I need to know in order to replace the window switch for the front pass...
How do I remove the housing for the air filter so I can replace my battery?
Check engine light came on and car went into limp mode. Mechanic reset it and it did it again...