Estimates last updated October 16, 2025

1992 Volkswagen Corrado Neutral Safety Switch Replacement Cost

The average cost for a 1992 Volkswagen Corrado Neutral Safety Switch Replacement is between $287 and $361.

Labor costs are estimated between $159 and $233 while parts are typically priced around $128.
This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.

Neutral Safety Switch Replacement

What is a neutral safety switch?

When starting a vehicle, if the automatic transmission is not in neutral or park, the neutral safety switch will prevent the engine from starting.

How does the neutral safety switch work?

To protect the vehicle, there is a switch installed on most automatic and dual clutch transmissions which disallows the engine from starting when the transmission is not placed in neutral or park. Some models use input from the transmission control unit to determine the vehicle's transmission position, but others use a physical switch. Both systems function to interrupt the starting circuit when the transmission is not in park or neutral.

What are the symptoms related to a bad neutral safety switch?

When the neutral safety switch fails, the vehicle will either start in any gear, or will not start in any gear. In many cases, the vehicle will start in neutral, but not in park. Some vehicles may store on-board diagnostic (OBD) trouble codes which reference the transmission, but, most commonly, there will be no diagnostic trouble codes stored in the vehicle's memory for this issue, as the computer cannot recognize this failure in most cases.

Can I drive with a neutral safety switch problem?

Driving with a faulty neutral safety switch is generally impossible , but if the vehicle will start and change gears like normal, driving should not pose any issues. If the vehicle will not start, it will require a tow to a repair facility. Get this fixed by a RepairPal Certified Shop

How often do neutral safety switches need to be replaced?

MAF sensors do tend to fail sometime in many vehicles. Failure rates are highest between 100,000 and 150,000 miles, but this is only an average. The sensor can also be damaged by road debris in many vehicles, or anytime the transmission is serviced or repaired. Lastly, a collision may cause a physical or electrical fault in the neutral safety switch. Vehicles with internal neutral safety switches will benefit from proper maintenance, and may fail prematurely when the transmission is neglected.

Volkswagen Neutral Safety Switch Replacement Cost Estimates

The average cost for a Neutral Safety Switch Replacement is between $287 and $361 but can vary from car to car.

Volkswagen Corrado Neutral Safety Switch Replacement Cost by Year

The average cost for a Volkswagen Corrado Neutral Safety Switch Replacement is between $287 and $361 but can vary from car to car.

1994 Volkswagen Corrado

$299-$373

1993 Volkswagen Corrado

$299-$373

1992 Volkswagen Corrado

$287-$361

1991 Volkswagen Corrado

$287-$361

1990 Volkswagen Corrado

$287-$361

Neutral Safety Switch Replacement

Jump to:Commonly associated repairs Cost estimates by vehicle Cost estimates by year

What is a neutral safety switch?

When starting a vehicle, if the automatic transmission is not in neutral or park, the neutral safety switch will prevent the engine from starting.

How does the neutral safety switch work?

What are the symptoms related to a bad neutral safety switch?

Can I drive with a neutral safety switch problem?

How often do neutral safety switches need to be replaced?

How are neutral safety switch issues diagnosed?

The neutral safety switch is quickly diagnosed by testing the switch, and related components attached to the gear selector inside the vehicle. A faulty neutral safety switch will most likely be removed and bench tested for confirmation of failure.

How is a neutral safety switch replaced?

Replacement of a steering knuckle on most vehicles is an advanced DIY repair that requires tools, equipment, and experience necessary to remove pressed hubs and bearings (including snap rings that retain the bearings), and to press the components into the new steering knuckle. The ball joints and tie rod end also need to be separated. The vehicle needs to be safely lifted in the air with a jack and jack stands to perform this repair. If you are not comfortable with these repair procedures, it would be wise to find a professional technician for the job.

RepairPal Recommendations for neutral safety switch issues

We always recommend contacting the dealership parts department for revised part numbers. There may be a new part number for the neutral safety switch, and possibly the transmission fluid. When new part numbers are issued, this may be due to a redesigned part that fixes known flaws, or an update. Aftermarket sensors may not have these benefits.

What to look out for when dealing with neutral safety switch issues

There are many types of transmission fluids, and they are not typically interchangeable. Consulting the owner's manual for your vehicle is the best way to ensure you have the correct fluid for your transmission. If improper transmission fluid is added, the resulting damage could be severe.

Can I replace the neutral safety switch myself?

Replacing the neutral safety switch at home could be done for more experienced DIYers. The person completing the repair must have an understanding of how the switch functions, how the switch is sealed against transmission fluid leaks, and how to diagnose the switch. If any of these areas are unclear, or if the switch is internal to the transmission, a trusted professional should complete this repair.