Learn About Your Car

Are you interested in certification?

PCV Valve Replacement

What is a pcv valve?

The positive crankcase ventilation (PCV) valve and hose connect the engine crankcase, where the crankshaft is installed, to the intake manifold, allowing the lower half of the engine to release gases and pressure when the engine is operating.

How does the pcv valve work?

As the engine operates, small fires inside each engine cylinder create pressure that pushes the engine piston down, toward the crankshaft, and some combustion gases from the fire in the cylinder are able to get around the piston, and enter the crankcase. Also, heat from the engine causes the air inside the crankcase to expand. If this condition were left untreated, the engine would develop leaks, and would suffer severe inefficiency, if it ran at all. To prevent this situation, the crankcase ventilation system connects the crankcase to the intake manifold. The intake manifold is constantly under vacuum as the engine sucks in air, so when the crankcase ventilation valve is installed, the hot gases are sucked from the engine crankcase, and burned in the engine as fuel.

Failed PCV valves can cause the engine to idle roughly and the Check Engine Light to illuminate.

Mercury PCV Valve Replacement Cost Estimates

The average cost for a PCV Valve Replacement is between $76 and $119 but can vary from car to car.

Mercury Grand Marquis

Mercury Villager PCV Valve Replacement Cost by Year

The average cost for a Mercury Villager PCV Valve Replacement is between $76 and $119 but can vary from car to car.

2002 Mercury Villager

$75-$117

2001 Mercury Villager

$75-$117

2000 Mercury Villager

$75-$117

1999 Mercury Villager

$75-$117

1998 Mercury Villager

$76-$119

1997 Mercury Villager

$76-$119

1996 Mercury Villager

$76-$119

1995 Mercury Villager

$76-$119

1994 Mercury Villager

$76-$119

1993 Mercury Villager

$76-$119

Show All Years

More RepairPal Resources

PCV Valve Replacement

Jump to:Commonly associated repairs Related OBD codes Cost estimates by vehicle Cost estimates by year

What is a pcv valve?

How does the pcv valve work?

Failed PCV valves can cause the engine to idle roughly and the Check Engine Light to illuminate.

Estimates last updated June 18, 2026

1997 Mercury Villager PCV Valve Replacement Cost

The average cost for a 1997 Mercury Villager PCV Valve Replacement is between $76 and $119.

Labor costs are estimated between $61 and $90 while parts are priced between $15 and $29.
This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.
For a more accurate estimate based on your location, use our Fair Price Estimator below.

A plugged PCV system can cause engine oil leaks. It's important that the shop checks and eliminates any issues with the PCV system while repairing engine oil leaks.

What are the symptoms related to a bad pcv valve?

Rough idling, lack of power, engine oil leaks, engine burning oil, and illumination of the check engine light are all possible if the PCV valve has clogged. If the check engine light comes on, the on-board diagnostics (OBD) trouble codes will most likely relate to manifold vacuum, air and fuel mixture, PCV system, mass airflow sensor readings, and exhaust and emissions readings. These are all affected in the event the PCV valve is clogged, is stuck fully open, or is stuck fully closed, however, if the valve is stuck fully open, the engine oil seals are not in danger of overpressure.

Can I drive with a pcv valve problem?

Driving with the PCV valve stuck closed or clogged is not recommended. If the vehicle must be driven, keeping the engine speed low is the safest bet, as this will also decrease the amount of pressure in the crankcase. If the PCV valve is stuck open, there is no harm in driving, however, the vehicle may experience poor fuel mileage, vibrations, and the dreaded check engine light as the computer registers this condition as a vacuum leak.

How often do pcv valves need to be replaced?

PCV valves are a common repair since they are part of the factory scheduled maintenance plan. PCV valves are recommended from 35,000 -60,000 miles, with most being right at the 50,000 mile mark. Many turbocharged engines require more frequent changes, and may have a secondary PCV valve in the PCV system. PCV valves often fail early, mostly due to a lack of maintenance. If the engine oil turns sludgy, that sludge will build up on the PCV valve, quickly clogging the valve, and necessitating replacement.

How are pcv valve issues diagnosed?

Understanding what the PCV valve does make diagnostics a breeze for anyone. If the technician suspects the PCV valve has failed, he will remove the valve, and use his hand-help pump to apply vacuum, then forced air, to see how the PCV reacts. If air can freely move through the valve in the intended direction, it is working properly. The valve has failed the test if air moves through in both direction or neither direction, or if air only moves in the wrong direction.

How is a pcv valve replaced?

Replacing the PCV valves can take seconds on some vehicles, and even an hour or two on others. In all cases, replacing the part is easy, but accessibility is not always on the technician's side. Vehicle are purpose-built, and most are built to be economical and reliable. This means placing components that frequently fail in expected positions, and unobstructed from removal. For vehicles that are built for high-luxury, performance, or off-road use, the placement of components is strictly for the purpose of enhancing performance, and may be very complicated to service.

PCV valves are a regularly scheduled maintenance item and are replaced to keep the engine running optimally.

Get a RepairPal Fair Price Estimate® for your 1997 Mercury Villager.

Our Fair Price Estimate will help you avoid overpaying based on your car, needed service, and labor rates in your area.