Estimates last updated October 16, 2025

2012 BMW 650i Clutch Master Cylinder Replacement Cost

The average cost for a 2012 BMW 650i Clutch Master Cylinder Replacement is between $779 and $1,036.

Labor costs are estimated between $549 and $806 while parts are typically priced around $230.
This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.

Clutch Master Cylinder Replacement

What is a clutch master cylinder?

The hydraulic clutch uses a clutch master cylinder to compress fluid inside the system, causing the slave cylinder to operate the clutch.

How does the clutch master cylinder work?

The clutch pedal is a lever that increases the amount of force you apply. When the clutch is pressed, the clutch master cylinder pushes fluid through the line, and into the slave cylinder on the other end. The slave cylinder pushes on the clutch fork, which disengages the clutch. When the clutch pedal is released, the clutch pushes the slave cylinder closed, forcing fluid back into the master cylinder, which lifts the clutch pedal and provides the force felt when pressing the clutch.

What are the symptoms related to a bad clutch master cylinder?

If the clutch master cylinder fails, the clutch pedal may float to the floor when held, and the vehicle may attempt forward motion with the vehicle stopped and in gear. The clutch will attempt to engage as the fluid escapes compression in the master cylinder. In most cases, the clutch pedal will have little to no effect on the clutch.

Can I drive with a clutch master cylinder problem?

Driving a vehicle without a working clutch is only possible if the transmission is shifted improperly, and push-started at every stop. While this may save a few dollars on wrecker services, it can cost the replacement of the manual transmission. It is better to have the vehicle towed, than risk further damage.

How often do clutch master cylinders need to be replaced?

BMW Clutch Master Cylinder Replacement Cost Estimates

The average cost for a Clutch Master Cylinder Replacement is between $779 and $1,036 but can vary from car to car.

BMW 650i Clutch Master Cylinder Replacement Cost by Year

The average cost for a BMW 650i Clutch Master Cylinder Replacement is between $779 and $1,036 but can vary from car to car.

Clutch Master Cylinder Replacement

Jump to:Cost estimates by vehicle Cost estimates by year

What is a clutch master cylinder?

The hydraulic clutch uses a clutch master cylinder to compress fluid inside the system, causing the slave cylinder to operate the clutch.

How does the clutch master cylinder work?

What are the symptoms related to a bad clutch master cylinder?

Can I drive with a clutch master cylinder problem?

How often do clutch master cylinders need to be replaced?

The clutch hydraulic system, including the clutch master cylinder, clutch slave cylinder, and fluid lines, will need replacement sometime during the serviceable life of most equipped vehicle's. They wear out with use, but this typically takes well over 100,000 miles of use. For vehicle's used in city driving, the system will require much more maintenance over the life of the vehicle. Changing the clutch fluid according to the manufacturer specified intervals may help prevent premature failure of these components.

How are clutch master cylinder issues diagnosed?

Clutch master cylinder failure is most evident when the slave cylinder actuates properly, but pressure bleeds off while holding the clutch pedal. This means, that as the clutch pedal is held, the slave cylinder will slowly allow the clutch to engage, but is free of leaks, and in good condition. Normally, a leaking clutch master cylinder is a give-away. In most cases it is recommended to change the slave cylinder at the same time, as the master cylinder failing may be an indication of overall system condition. It is much more economical to replace both during the same service.

How is a clutch master cylinder replaced?

Replacing the clutch master cylinder requires that the fluid from the system is drained. Also, it is normally recommended to replace the clutch slave cylinder at the sale time. After draining the system of fluid, the slave cylinder and master cylinder will be removed from the vehicle by disconnecting the slave cylinder from the transmission bell housing, and removing the master cylinder from the firewall. The clutch hydraulic line should be removed with the slave cylinder and clutch master cylinder. Once separated from the vehicle, the new components will be fitted, and the line replaced if necessary. Installation is the reverse of removal, and once the system is in place, the system must be bled of air, and tested.

RepairPal Recommendations for clutch master cylinder issues

We recommend OEM quality or better replacement parts for the clutch hydraulic system. Inferior products can lead to repeated repairs, and result in greater costs in the future.

What to look out for when dealing with clutch master cylinder issues

The clutch fork easily falls off of many transmissions when the clutch slave cylinder is removed. If the clutch fork is not properly installed, the clutch will not function properly, and damage to the clutch throw out bearing may result.

Can I replace the clutch master cylinder myself?

This task is recommended to the DIYer who completely understands the clutch hydraulic system. If knowledge of this system is lacking or the procedures for replacing, bleeding, and filling are not understood, this task should be trusted to a certified professional.