2008 Toyota Yaris Crankshaft Position Sensor Replacement Cost in Sacramento, CA

Labor 40%

$61 - $90

Parts 60%

$97 - $135

The average cost in Sacramento, CA for a 2008 Toyota Yaris Crankshaft Position Sensor Replacement is between $158 to $225. This does not factor in taxes and fees, and related repairs.

REPAIRPAL CERTIFIED SHOPS™

Find the best certified local repair shops.

Experience and quality you can trust

Upfront fair pricing – everytime.

Minimum 12k / 12-month warranty

Providing trusted repair shops to thousands of car owners and partners:

Cost Comparison Overview Fair Price Estimate Related OBD-II Codes

Cost Comparison Overview Fair Price Estimate

Cost in Sacramento, CA vs. Other Cities

Compare the average cost of replacing a Crankshaft Position Sensor Replacement in various locations to see how prices differ from those in Sacramento, CA.

If you're looking for the most accurate cost for your 2008 Toyota Yaris, get a Fair Price Estimate™ that is honored by all our RepairPal Certified shops.

Sacramento, CA

$158 to $225

What is a crankshaft position sensor?

The crankshaft position sensor is located near the engine's crankshaft, and relays information about the crankshaft’s position as it rotates.

How does the crankshaft position sensor work?

As the crankshaft spins, the position sensor magnetically reads its position. This information is constantly sent to the engine's computer for comparison with data from the camshaft position sensor. When the two signals reach the computer, they must match; otherwise, the computer will think there is a mechanical error in the engine and will adjust some settings in response.

What are the symptoms related to a bad crankshaft position sensor?

When the computer senses the engine is out of time, it will turn on the check engine light, and the engine may start and stall, or fail to start at all. If the engine runs, it will run poorly, and get bad fuel mileage. » LEARN MORE: Symptoms of a bad crankshaft position sensor

Can I drive with a crankshaft position sensor problem?

Driving a vehicle with a failed camshaft or crankshaft position sensor is usually impossible. If driving is possible, it is not recommended. If the sensor is functioning normally and reporting an error, the engine may be out of time or may have suffered a mechanical failure.

How often do crankshaft position sensors need to be replaced?

There's no set replacement interval for the crankshaft position sensor, and on many cars, the part will last the lifetime of the vehicle. It's not uncommon for it to fail, however, and the likelihood increases once you pass 100,000 miles.

How are crankshaft position sensor issues diagnosed?

Using a professional-grade scanner, a mechanic can read where the sensors think the crankshaft and camshaft are, and compare this to their actual position. If the reading from either sensor is incorrect, the sensor will be tested and replaced if necessary.

How is a crankshaft position sensor replaced?

To replace the crankshaft position sensor, you have to disconnect any electrical connectors and then unscrew the sensor. Sealant may be applied before inserting the new sensor into the engine. On some vehicles, the crankshaft position sensor is located inside the engine block, and significant deconstruction is required to get to it. In these cases, we recommend trusting a professional technician with the repair.

RepairPal recommendations for crankshaft position sensor issues

Make sure to use high-quality, OEM sensors. Lesser products will likely cause a repeated repair. When checking this sensor, the vehicle's timing belt should be inspected as well. If the timing belt or timing chain has failed, it should be replaced and the engine should be further inspected.

Can I replace the crankshaft position sensor myself?

Replacing this sensor is easy enough — but what's often tricky is getting the correct diagnosis. Unless you have the proper scanning tools and knowledge, it's likely best to let a professional technician handle this diagnosis and repair.

Get a Fair Price Estimate™

RepairPal offers free estimates for hundreds of repair and maintenance services. Each estimate includes:

30-day price guarantee

Breakdown of part & labor costs

Minimum 12,000-mile / 12-month warranty

OBD Codes Related to Crankshaft Position Sensor Replacement

P0317: Rough Road Hardware not Present P0318: Rough Road Sensor "A" Signal Circuit P0319: Rough Road Sensor "B" Signal Circuit

Join thousands of car owners using RepairPal.

"You certainly provide a service which allows a customer to feel more confident that they are being serviced at a reasonable price."

Gerald

Lawrenceville, GA

"I'm so happy that I found RepairPal. This site really simplifies the process of finding fair prices on parts and labor. Plus, I found a new great mechanic!"

Lizzy

Minneapolis, MN

"I liked the convenience of RepairPal, and knowing the cost before the repair. Also, I liked the standards and expectations put in place by RepairPal; it takes all of the questions out of the process."