BMW 328Ci Spark Plug Replacement Cost

The average cost for a BMW 328Ci Spark Plug Replacement is between $223 and $390.

Labor costs are estimated between $171 and $251 while parts are priced between $52 and $139.

Spark Plug Replacement

What is a spark plug?

Spark plugs are a crucial part of the vehicle’s ignition system. They provide the spark that ignites the air-fuel mixture inside the engine, creating the chain-reaction that generates the engine’s power.

How does the spark plug work?

The spark plug turns high voltage electricity from the ignition coil into a strong spark inside the engine. This ignites the air-fuel mixture, creating power.

What are the symptoms related to a bad spark plug?

When spark plugs fail, the engine will struggle. The check engine light will come on, and it may appear either solid or flashing. The driver would likely notice one or more of the following: engine vibrations, rough idling, poor gas mileage, excessive cranking time needed to start the engine, and power loss or surging. In extreme circumstances, the engine may stall or fail to start.

Can I drive with a spark plug problem?

The car will run with a spark plug problem, but it's not wise to keep driving it this way. If a spark plug isn't working, unburned fuel from the engine will get into the exhaust at a higher rate, causing problems for the catalytic converter. If the converter gets ruined by this unburned fuel, it will lead to a costly repair.

How often do spark plugs need to be replaced?

Spark plugs do eventually wear out, and failure is most common after 100,000 miles of use under normal driving conditions. But that can be greatly shortened by harsh conditions or leaking fluids.

BMW 328Ci Spark Plug Replacement Cost by Year

The average cost for a BMW 328Ci Spark Plug Replacement is between $223 and $390 but can vary from car to car.

2000 BMW 328Ci

$223-$390

BMW Spark Plug Replacement Cost Estimates

The average cost for a Spark Plug Replacement is between $223 and $390 but can vary from car to car.

Spark Plug Replacement

Jump to:Cost estimates by year Commonly associated repairs Related OBD codes Cost estimates by vehicle

What is a spark plug?

How does the spark plug work?

The spark plug turns high voltage electricity from the ignition coil into a strong spark inside the engine. This ignites the air-fuel mixture, creating power.

What are the symptoms related to a bad spark plug?

Can I drive with a spark plug problem?

How often do spark plugs need to be replaced?

Spark plugs do eventually wear out, and failure is most common after 100,000 miles of use under normal driving conditions. But that can be greatly shortened by harsh conditions or leaking fluids.

How are spark plug issues diagnosed?

If the spark plugs are suspected, they're checked for proper connection with the ignition coil. If that's OK, the plugs must be removed, and the spark plug gap must be checked. If the gap is too small because of corrosion, or too large because or deterioration, they will be replaced. If the spark plug is in good condition, a tester is used to find whether the spark plug is able to produce spark.

How is a spark plug replaced?

On newer vehicles, spark plug replacement involves removing the engine cover, ignition coil harness and ignition coils, and then finally the spark plugs. For most older vehicles, removing the spark plug wires and spark plugs is all that's required. Once the spark plugs are removed, the gap on the new spark plug is set, and the plug is installed using an anti-seize compound and proper torque. Prior to reinstalling the spark plug wire or ignition coil, dielectric grease is applied to the spark plug terminal to promote the transfer of electricity.

What to look out for when dealing with spark plug issues

The cost of spark plug replacement can be surprisingly low or very high — it all depends on how many spark plugs need to be replaced, how hard it is to get to them, and how much diagnosis is required to identify them as the problem.

Can I replace the spark plug myself?

Replacing your spark plugs can be one of the easiest or most frustrating experiences you can have. If your plugs are easy to access, it's usually a simple repair. But if the plugs are hidden away, requiring a lot of disassembly, you may be better off having a repair facility handle the job. If you choose to do it yourself, ensure you have the proper spark plug gap, use anti-seize compound on the threads, use dielectric grease on the spark plug terminal, and make sure the threads go in straight before attempting to tighten to the manufacturer's specifications.