Question Asked: Navigation System.
August 30, 2014, 06:00 PM
I have upgraded the CD several times. Most of the time it will not work. I get an error message. When it loads, it works just fine. When it doesn't, there is an error message. Sometimes it will even flash back and forth from error to loading.
Question Asked: Heat Shield above muffler.
August 30, 2014, 04:55 PM
I need to replace muffler and tailpipe. I looked underneath tonite and found the heat shield hanging on by 1 rusty bolt. At least 2 have rusted out and that is why it lays on muffler or drive shaft and rattles. Is this the same recall as listed in newer model recalls?
Question Answered: What is going on with my rear breaks?
August 30, 2014, 05:42 PM
Have your brakes and rotors checked now. If your car has rear drum brakes, you may need brake shoes etc. With the drum brakes, there could be several things wrong with the brakes.
Question Answered: about the brakes
August 30, 2014, 05:28 PM
I don't know if it's common. Check your brake fluid level in your master cylinder. You may be low on brake fluid….and you also may have a leak in a brake line or hose.
Question Answered: How often should I have to add oil?
August 30, 2014, 05:24 PM
You are in trouble (unless the light is bad). If you are using that much oil, you've either got a bad leak or you are burning a lot of oil.
Question Answered: Why does my air/heat only work at the highest setting?
August 30, 2014, 04:48 PM
Replace your fan resistor module located behind glove box. Same happened to me. Eventually the fan won't work at all. After some months, my blower motor stopped. I just replaced it today. I have an extra resistor. I'll sell it to you for $12.00 if you want. It's brand new. I bought a second one because mine stopped again. I was hoping it was the resistor again, but it turned out to be the blower motor. Bought at Auto Zone for $103.00. If you buy your own resistor, you should be able to buy $15 to $25. DO NOT get at a Chrysler dealer!! They will rape you on the part and labor.
Question Answered: My AC will not turn on
August 30, 2014, 04:42 PM
My fan would only work on high setting. Then it stopped. I replaced the fan resistor (located behind glove box). That worked for about 3 months. Just today, I replaced the fan blower motor. That was the problem. I had heat and A/C but the fan was not pushing it through the vents. If your problem is the same as mine, there is only 3 or 4 parts to check. There is a 40 amp fuse (should be #1 in fuse box, another cube type fuse in # 30), the fan resistor module ( should be able to get from $15 to $25). The last is the fan blower motor. I paid $103 at Auto Zone. I am no mechanic!! I installed both pieces in less than 1/2 hour. If you go to a Chrysler dealer you will get raped on parts and labor. If your issue is different, then sorry.
Problem Reported: Exhaust Manifold Bolts May Break
May 27, 2010, 11:09 AM
<p>Broken <a id="ce_69" class="ct_selected tooltip" href="/exhaust-manifold">exhaust manifold</a> bolts can create an exhaust leak; the <a id="ce_70" class="ct_glossary tooltip" href="/exhaust-manifold-gasket">exhaust manifold gaskets</a> and bolts should be replaced.<strong><br /></strong></p>
Car Review: 2002 Jeep Liberty
August 30, 2014, 05:15 PM
My 2002 Limited has 121,000 miles. I bought it new. The first9 or 10 years, only normal maintenance, brakes,sensors, battery, tires. Since then I've replaced another battery, ECM (computer module), hood support lifts, rear hatch lifts, driver seat splash guard, the seat recliner mechanism broke (expensive repair) driver's leather seat splitting, check engine light on for major evap leak, fan resistor module stopped working (replace it) then the blower motor went (replaced it). The stainless steel exhaust lasted about 10 years. Will be putting my third muffler in 4 years and tailpipe. I noticed the heat shield has rusted and is laying on the muffler. The biggest issue is rust. Front doors , at the top of windshield, both sides of third brake light, hatch lift support rusted off. To fix that you have to replace the entire rear window. The clamp is moulded into the glass $400 to $500 for privacy glass. Not counting labor.