Close

2014 Honda Accord Problems

RepairPal has identified the most common problems with the 2014 Honda Accord based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
11
Known Problems

The Air Conditioning Condensers can fail due to damage from road debris due to a lack of protection for the condenser. 

The 1997-2017 Honda Accord May have problems with the EVAP canister vent solenoid. It stops responding to commands to open and close, and the following occurs:

  • Illumination of the check engine light
  • OBD trouble code P1457 is stored
  • Engine takes longer than usual to start
  • Fuel mileage decreases noticeably
  • The valve is located on the charcoal canister, and is meant to open and close upon command. It fails due to corrosion breaking one of two internal seals, which allows air to escape the system, signaling the OBD trouble code P1457.

    Correcting the problem can be done by replacing the vent valve, or, in some cases, cleaning and resealing the vent valve has been successful. You can get an estimate for this repair here.

    A worn, missing, or loose gas cap can cause the same issues.

    The 1990-2016 Honda Accord engine oil pressure sensor may leak from normal operation.

    More information about the oil pressure sensor here.

    To correct the leak, the sensor must be inspected, properly sealed and installed, or replaced with new.

    Ignition switch failure may cause the car to stall or fail to start. Honda issued a recall to replace the ignition switch. For more information on this recall please click here»

    Owners have reported a number of prematurely worn rear wheel bearings. As the bearing fails, a rotational humming or grinding noise may be noted from the rear as vehicle speed increases. Replacement of the rear hub assembly, which includes the bearing, would be necessary to remedy this condition.

    The Honda Accord may have issues with the idle air control system, causing:

    The idle air bypass system is made up of vacuum lines, an idle air control valve (IACV), the throttle body, and intake manifold, and allows enough air into the engine to idle when the throttle body is closed. The OBD trouble code P0505 refers you to this system to inspect for failures.

    The most likely cause is a dirty or failed IACV, but vacuum lines, intake manifold gasket, throttle body gasket, and IACV gasket should be inspected.

    In all cases involving the IACV, the throttle body ports should be cleaned prior to installing the IACV onto the throttle body.

     

    Honda Accord models may develop shifting issues with the automatic transmission accompanied by warning lights.  

    Rough shifting may occur, and the “D4” light and check engine may begin to blink. The check engine light will also illuminate, and OBD trouble codes P0700, P0730, P0740, P0780, P1768 and/or P1768 will be stored in the computer.

    If the transmission shifts roughly, the failure is very likely mechanical failure of the transmission. If the transmission performs normally, a faulty sensor, or dirty transmission fluid may be the case.

    In most cases, it is necessary to use professional diagnostic equipment to provide a diagnosis, and complete the repair.

    The longevity of the transmission is dependent on strict adherence to the manufacturer's recommendation for ATF replacement intervals and procedure.

    The front brake rotors can warp and cause a vibration when braking. You will feel vibrations in the brake pedal and the steering wheel. The rotors should be replaced to correct this issue. Using high-quality rotors is highly recommended. The OEM parts are best for brake repairs but some aftermarket rotors can work well. It's always good to ask your mechanic to use rotors they've seen the best results from. 

    Leaking gaskets around the tail lights can allow water entry into the tail light assembly. New gaskets should fix this concern.

    If the brake pedal feels hard the first time it is pressed in the morning, it could be due to a problem with the vacuum supply hose for the brake booster. A revised brake booster hose is available to address this concern.

    The ABS modulator (hydraulic unit) can leak air into the brake system and cause a low brake pedal. A new ABS modulator will be needed if it is diagnosed to be the source of the leak.