Close

2011 Honda Accord Problems

RepairPal has identified the most common problems with the 2011 Honda Accord based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
15
Known Problems

Honda Accord models may develop shifting issues with the automatic transmission accompanied by warning lights.  

Rough shifting may occur, and the “D4” light and check engine may begin to blink. The check engine light will also illuminate, and OBD trouble codes P0700, P0730, P0740, P0780, P1768 and/or P1768 will be stored in the computer.

If the transmission shifts roughly, the failure is very likely mechanical failure of the transmission. If the transmission performs normally, a faulty sensor, or dirty transmission fluid may be the case.

In most cases, it is necessary to use professional diagnostic equipment to provide a diagnosis, and complete the repair.

The longevity of the transmission is dependent on strict adherence to the manufacturer's recommendation for ATF replacement intervals and procedure.

The radio and climate control display can go dark on some models. It will be necessary to replace the affected unit to correct this concern. Some customers have reported receiving help from Honda regarding this repair.

It's very common for the front compliance bushings to crack and require replacement. You will most often be notified after an inspection while your Honda is in the shop for general maintenance. Some Honda owners have reported noises from the front suspension at low speeds and over bumps as well. The bushings are located in the front control arms and can be replaced separately from the control arm. 

Several symptoms can occur due to the power door lock actuators failing. These can include doors that don't lock, doors that lock themselves and doors that won't unlock. Often times these problems are intermittent and there's no rhyme or reason as to when the issues will occur.

Once it has been diagnosed and determined one of the door actuators is the problem, the part can not be repaired and must be replaced. 

The front brake rotors can warp and cause a vibration when braking. You will feel vibrations in the brake pedal and the steering wheel. The rotors should be replaced to correct this issue. Using high-quality rotors is highly recommended. The OEM parts are best for brake repairs but some aftermarket rotors can work well. It's always good to ask your mechanic to use rotors they've seen the best results from. 

The Air Conditioning Condensers can fail due to damage from road debris due to a lack of protection for the condenser. 

Owners have reported a number of prematurely worn rear wheel bearings. As the bearing fails, a rotational humming or grinding noise may be noted from the rear as vehicle speed increases. Replacement of the rear hub assembly, which includes the bearing, would be necessary to remedy this condition.

A water leak on the passenger floor can be caused by a clogged AC evaporator drain.

The Honda Accord may have issues with the idle air control system, causing:

The idle air bypass system is made up of vacuum lines, an idle air control valve (IACV), the throttle body, and intake manifold, and allows enough air into the engine to idle when the throttle body is closed. The OBD trouble code P0505 refers you to this system to inspect for failures.

The most likely cause is a dirty or failed IACV, but vacuum lines, intake manifold gasket, throttle body gasket, and IACV gasket should be inspected.

In all cases involving the IACV, the throttle body ports should be cleaned prior to installing the IACV onto the throttle body.

 

Damaged engine mounts can lead to vibration and roughness felt in the steering wheel. A rattle in the dash and engine area may also be heard. Replacement of damaged mounts will commonly correct these issues.

The driver's door latch assembly can break internally, which causes the door to stay closed. The interior and exterior door handles do not work to open the door. Our technicians note that the door panel must be removed while the door is closed (likely damage will occur) and the latch assembly must be drilled in a specific spot for the door to open.

The 1990-2016 Honda Accord engine oil pressure sensor may leak from normal operation.

More information about the oil pressure sensor here.

To correct the leak, the sensor must be inspected, properly sealed and installed, or replaced with new.

The 1997-2017 Honda Accord May have problems with the EVAP canister vent solenoid. It stops responding to commands to open and close, and the following occurs:

  • Illumination of the check engine light
  • OBD trouble code P1457 is stored
  • Engine takes longer than usual to start
  • Fuel mileage decreases noticeably
  • The valve is located on the charcoal canister, and is meant to open and close upon command. It fails due to corrosion breaking one of two internal seals, which allows air to escape the system, signaling the OBD trouble code P1457.

    Correcting the problem can be done by replacing the vent valve, or, in some cases, cleaning and resealing the vent valve has been successful. You can get an estimate for this repair here.

    A worn, missing, or loose gas cap can cause the same issues.

    The 2013-2012 Honda Accord has brake caliper issues, which are known for causing vibration and grinding noises at all times.

    The brake rotor is a disk that sits between two brake pads. The brake pads are squeezed against the disk by what is called a brake caliper. When that caliper gets stuck, the brake pads are permanently pressed against the rotor causing:

  • Vibration in brake pedal
  • Vibration on steering wheel
  • Illumination of the ABS or brake warning light
  • Grinding noise from one corner of the vehicle
  • Vehicle pulls to one side of the road
  • Braking requires more pressure on the brake pedal
  • The repair for a seized brake caliper, the brake pads, brake rotor, and brake caliper must be replaced or vibration will remain after the new caliper is installed. Changing the brake fluid and flushing the brake system according to manufacturer specified intervals can help improve longevity of the brake caliper.