2007 Mercedes-Benz CLK350 Problems

RepairPal has identified the most common problems with the 2007 Mercedes-Benz CLK350 as reported by actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

Refine by vehicle
×
Choose your vehicle
21
Known Problems

The Mercedes Benz CLK350 may have engine oil seeping or leaking from the back of the cylinder heads. This is commonly misdiagnosed as leaking valve covers.

On the back of the cylinder heads there are three, in total, plastic expansion plugs that plug access ports to the camshafts. These plugs are well known for seeping oil, and leaking if left unattended. The oil will run down the back of the engine and eventually make it to the ground. 

Replacement of these three plastic plugs is extremely simple, and should be done as regular maintenance. The recommended interval for replacement is every 60,000 miles.

The engine in the CLK350 is known by Mercedes Benz to have issues due to a poorly manufactured gear on the balance shaft (also known as the counter-rotating assembly). Since the balance shaft gear is driven by the timing chain, which keeps the engine rotating synchronously, when it fails, the timing of the engine will change causing:

-Illumination of the Check Engine Light

-Rough Running Conditions

-Stalling

-Loud Rattle or Slapping Noise

-OBD Trouble Code P1200 and P1208

Correction for this issue is replacement of the balance shaft, or balance shaft gear. Replacement of the timing chain and tensioner should be done as well. The Mercedes Benz dealer may cover some or all of the repair cost on select vehicles as a result of a class action settlement.

The power steering reservoir designed for the 2006-2014 Mercedes Benz CLK350 commonly leaks power steering fluid causing a screeching sound when turning the steering wheel, especially when the vehicle is stopped. The power steering light may illuminate on the dash for more severe leaks.

This is caused by cracking in the plastic reservoir, or a hardened, brittle seal between the power steering reservoir and power steering pump.

Remediation involves replacing the power steering fluid reservoir, power steering fluid, bleeding the system of air, and replacement of the seal between the reservoir and power steering pump.

When starting the engine after sitting for several hours, a knocking sound may be heard for several seconds. This is a common issue with the 2006-2009 Mercedes Benz CLK350. There are three common problems that can cause this sound to occur:

-Oil pressure building too slowly, allowing for movement between the crankshaft and crankshaft bearings

-Stretch or wear of timing chain and components

-Balance shaft (counter rotating shaft) gear wear

The remediation for these problems can be crankshaft bearing replacement with correct size, replacement of timing components, or balance shaft replacement.

Going over large bumps in convertible models may cause the roll bar to deploy, rendering the roof inoperative. Special tools are generally required to return the roll bar to its stowed position.

The camshaft adjuster solenoid (which is related to the variable valve timing system) may fail or timing chain/balance shaft components may wear, resulting in illumination of the Check Engine Light and various drivability issues. Mercedes-Benz has released a service bulletin outlining specific repair instructions depending on fault codes stored.

The crankshaft position sensor may fail. Symptoms of this are: The engine will crank—but not start—especially when the engine is warm. The car may start again if it is left to cool off, but it may run roughly or have poor performance. Communicating these specific symptoms to your technician can save diagnostic time.

As a way to increase braking performance, the brake pads and rotors are make of a softer material and may be in need of replacement after approximately 20,000 miles; owners should be vigilant about getting their brakes checked.

Vehicles equipped with a 7-speed automatic transmission may develop a rough shifting condition, most commonly going up from first to second gear and going down from third to second or second to first gear. Our technicians tell us this is due to an internal component failure. Mercedes has released updated parts; the transmission will need to be removed and disassembled to complete the necessary repairs.

Computer control modules for the seats and doors, the CD changer, and the brake lamp switch tend to fail.

Ball joints can wear out prematurely, causing wear in the tires.

The sway bar end link joints may wear and cause a knocking noise over bumps. Loose or warn links should be replaced to correct this type of noise.

The hold down nut for the upper front strut area can become loose, causing a knocking noise. This can be repaired without removing the strut assembly.

High mileage or older vehicles commonly develop leaks from the differential seals and/or cover. Our technicians recommend a complete reseal of the differential unit whenever these leaks are repaired.

A vibration felt through the center floor of the vehicle can be caused by driveshaft flex discs, which crack and shred, causing excessive driveshaft movement. Not repairing these can cause damage to the driveshaft center support bearing, or, in the worst case scenario, damage to the transmission or differential.