1997 Dodge Ram 2500 Problem Reports

Most Reported 1997 Dodge Ram 2500 Problem Reports

Report A Problem
View:Most ReportedNewestRepairPal Verified

If the engine is difficult to start or cranks but does not start, it can be caused by a leak in the return side of the fuel system. This type of leak can allow air to enter the injection pump resulting in starting issues. A rubber hose on the back of the injection pump, connecting the pump to the steel hard line, that can be the source of this type of leak.

On 3.9L V6 and 5.9L V8 engines, the intake manifold gasket may leak and cause increased oil consumption and a spark knock during acceleration; the gasket should be replaced.

Engine overheating can result from coolant leaks which are commonly found at the thermostat housing gasket, water pump, heater return tube O-ring at the water pump, intake manifold gasket, and timing cover gasket. Our technicians recommend a complete inspection of the cooling system after any repairs are made to be sure there are no other leaks.

Some models could have a severe drift or pull to one side when the brakes were applied. If this is not caused by a dragging brake caliper, there is a service bulletin describing the step-by-step diagnosis and many possible solutions. Our technicians note the most common solutions are performing a four wheel alignment, checking torque on suspension components, installing shims between the wheels and hubs, and replacing the suspension arms.

If a Check Engine Light illuminates indicating leak detection pump (LDP) failure, the cause is often pinched or disconnected vacuum lines to the pump. Vacuum lines should be inspected before replacing the leak detection pump. Contamination (carbon or debris) in the pump can cause failure and any hoses should be cleared before a new pump is installed.

The AC/heater (HVAC) system may unexpectedly switch to the defrost mode when accelerating. This system is operated by engine vacuum and should be inspected for any vacuum leaks if this problem develops.  There is also a revised vacuum check valve available to address this concern.

On the 3.9L V6, 5.2L V8 and 5.9L V8 the Oil leaks commonly from the valve cover gaskets, intake manifold gaskets (front and rear), timing cover gaskets, distributor O-ring, and the rear main seal area. Using fluorescent engine oil dye can be helpful in determining the source(s) of the oil leak.

On the 3.9L V6 and 5.2L V8, rerouting the ignition coil wire and spark plug wires can help solve a misfire and/or surge problem that occurs at approximately 45 mph. A service bulletin was published that outlines the specifics of the repair. It states the rerouting procedure should be performed before other repairs are done for misfires, surging or spark knock.

One the 3.9L V6 and 5.9L V8 the carbon buildup on the top of the piston is common. As the buildup increases with mileage and over time, symptoms may vary from light ticking, to ticking/hammering, to hammering/knocking noises. Fuel injector cleaner often solves the problem.

On the 3.9L V6 and 5.9L V8 the engine oil leaks at the distributor can be misdiagnosed as leaks from the intake manifold seal, oil pan gasket, or rear crankshaft (rear main) seal. A revised distributor is available if oil is found inside the distributor.

When driving over bumps a clicking or squeaking from the rear leaf springs may be fixed by replacing the (leaf) spring tip liners and installing a spring clinch clip (kit available from the dealer).

Installing a foam pad between the inner door panel and the door can repair a buzzing caused by the door speaker.


A loud buzzing or whining when the transmission is in reverse may be caused by a regulator valve in the transmission valve body. A revised valve was released that does not resonate. Careful diagnosis should be performed because other causes can create the noise.

Inspect for pulley alignment if the drive belt is damaged on the inside edge. The crankshaft pulley may become loose on the crankshaft and should be inspected for fit.

Battery acid can leak on, and deteriorate a vacuum hose for the speed (cruise) control system. If the hose becomes loose or leaks vacuum, the speed (cruise) control will not function.