Close

1998 Acura CL Problems

RepairPal has identified the most common problems with the 1998 Acura CL based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

No car image 94a1663db56199c5353592009e34aaa51078a2469bed068bb8d6f0ba43accf97
Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
6
Known Problems

The Acura 3.2CL may develop issues with the automatic transmission.

Rough shifting may occur, and the “D4” light and check engine may begin to blink. The check engine light will also illuminate, and OBD trouble codes P0700, P0730, P0740, P0780, P1768 and/or P1768 will be stored in the computer.

If the transmission shifts roughly, the failure is very likely mechanical failure of the transmission. If the transmission performs normally, a faulty sensor, or dirty transmission fluid may be the case.

In most cases, it is necessary to use professional diagnostic equipment to provide a diagnosis, and complete the repair.

The longevity of the transmission is dependent on strict adherence to the manufacturer's recommendation for ATF replacement intervals and procedure.

The car will sometimes not start because of a problem with the ignition switch. Some models may have been recalled by Acura for this issue, please check with your dealer to be sure.

The 1998-2003 Acura CL may have issues with the idle air control system, causing:

The idle air bypass system is made up of vacuum lines, an idle air control valve (IACV), the throttle body, and intake manifold, and allows enough air into the engine to idle when the throttle body is closed. The OBD trouble code P0505 refers you to this system to inspect for failures.

The most likely cause is a dirty or failed IACV, but vacuum lines, intake manifold gasket, throttle body gasket, and IACV gasket should be inspected.

In all cases involving the IACV, the throttle body ports should be cleaned prior to installing the IACV onto the throttle body.

 

The Acura 3.2CL may develop issues with the automatic transmission.

Rough shifting may occur, and the “D4” light and check engine may begin to blink. The check engine light will also illuminate, and OBD trouble codes P0700, P0730, P0740, P0780, P1768 and/or P1768 will be stored in the computer.

If the transmission shifts roughly, the failure is very likely mechanical failure of the transmission. If the transmission performs normally, a faulty sensor, or dirty transmission fluid may be the case.

In most cases, it is necessary to use professional diagnostic equipment to provide a diagnosis, and complete the repair.

The longevity of the transmission is dependent on strict adherence to the manufacturer's recommendation for ATF replacement intervals and procedure.

The 1998-2003 Acura CL commonly has problems with the EVAP canister vent solenoid. It stops responding to commands to open and close, and the following occurs:

  • Illumination of the check engine light
  • OBD trouble code P1457 is stored
  • Engine takes longer than usual to start
  • Fuel mileage decreases noticeably
  • The valve is located on the charcoal canister, and is meant to open and close upon command. It fails due to corrosion breaking one of two internal seals, which allows air to escape the system, signaling the OBD trouble code P1457.

    Correcting the problem can be done by replacing the vent valve, or, in some cases, cleaning and resealing the vent valve has been successful. You can get an estimate for this repair here.

    A worn, missing, or loose gas cap can cause the same issues.

    The exhaust recirculation valve (EGR) on the 1998-2003 Acura CL may fail, causing:

  • Illumination of the check engine light
  • OBD trouble codes P0401 and P1491
  • Rough idle
  • Reduced fuel economy
  • Engine vibrations
  • Hesitation or stalling
  • Long cranking before engine starts
  • Failure of state or federal smog tests
  • The EGR valve has open and closed positions, and opens or closes on command from the computer.

    Exhaust gases constantly pass through the valve when it is open, leaving carbon deposits on the valve. These carbon deposits may lead the the valve sticking in the open or closed position.

    To correct this issue, sometimes it is sufficient to clean the valve, but replacement is recommended in all cases.

    For further information on your vehicle's issue, try out our diagnostics tool here.