At higher mileages, an anti-lock brake system wheel speed sensor may wear out and illuminate the ABS warning light. It is recommended to replace the sensor with a factory part and be sure to clean all rust and debris from the mounting area because the mounting distance is critical. Failure to do so may result in the new sensor setting false trouble codes. Be sure to check the condition and runout of the front wheel bearings on the 2WD and 4WD vehicles and the CV joints on the 4WD vehicles since worn wheel bearings and/or CV joints can cause the ABS trigger rings to rub against the ABS sensors and damage them.
Problems for specific Toyota Camry years:
Car problem reports
Problem with your car? See what our experts say or submit your own.
Repairpal verified 1996 Toyota Camry problems
The Check Engine Light may illuminate with code P0770 and/or P0773 stored. This would indicate a fault with the 3-way lock-up solenoid which could be defective and may need replacement.
The valve cover gaskets have a tendency to leak oil, especially the one near the firewall.
The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and the EGR Temperature sensor. Our technicians tell this repair is pretty straight forward and takes about 1-1.5 hours. It is also wise to verify the EGR system components i.e. the Transducer, EGR Valve and VSV Solenoid at this time.
Cars equipped with an automatic transmission might experience a hesitation when accelerating. Revised software for the on board computer is available which may correct this problem. Software revisions are commonly most helpful on newer vehicles. once the mileage builds up a worn component could cause similar problems. Whenever major transmission work in performed, the transmission software should be updated as necessary.
The Evaporative system may have problems with the vapor canister releasing charcoal pellets that plug the vent valve. Typically a Code P0441, P0442 and P0446 will be set. The key code is the P0446 which is a vent valve electrical failure. The proper repair is to replace the entire canister with all the valves as a unit. This is located on top of the fuel tank and is expensive. Our Technicians tell us that for awhile Toyota was covering these problems, but this may have changed. It would not hurt to call the dealer if this problem occurs to see if Toyota is still helping with these repairs.
If the vehicle will not crank over, the most common problem is the starter, which tend to fail at about 100,00-125,000 miles. Sometimes it is only the starter solenoid contacts, but often the complete starter (including solenoid) needs to be replaced.
On vehicles with a manual transmission, worn shift bushings can cause the transmission to pop out of gear, especially when coasting down in 1st or 2nd gear. Replacing all the shift linkage bushings is pretty straight forward and not expensive and will commonly correct this concern.
The pickup coil inside the distributor can fail and cause a no-start condition. There have also been some failures of the radio noise suppressors inside the distributor which can short out. It is recommended to replace the whole distributor with a complete genuine Toyota distributor if any of its components fail.
A loss of power on the freeway may due to an internally leaking fuel pulsation dampener. This commonly occurs on higher mileage vehicles.
The ignition coil inside the distributor may fail. Our technicians tell us this may result in a hesitation on acceleration, especially when the vehicle is warming up on cold, rainy days. The pickup coils inside the distributor can also fail and cause a no-start condition. There have also been some failures of the radio noise suppressors inside the distributors, which can short out. Our technicians recommend replacing the whole distributor with a complete, genuine Toyota distributor if any of its components fail.
The head gaskets are prone to leaks in as little as 60,000 miles. When the head gasket is replaced, the knock sensor harness should be replaced as well, as it can be damaged by leaky head gaskets, resulting in a serious decrease in fuel efficiency or in long term engine damage.
At 125,000-150,000 miles, the Brake Master Cylinder may need replacing. When replacing the master cylinder, it is critical to adjust the brake pedal to master cylinder pushrod clearance or the brakes can drag and overheat.
A rough idle and even an emissions inspection failure for high HC and CO can be caused by improperly adjusted valves. Also, exhaust valves may become to tight which can lead to valve failures. Our technicians tell us that regular valve adjustment inspections are a must.