Close

1996 Toyota Camry Problems

RepairPal has identified the most common problems with the 1996 Toyota Camry based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

No car image 94a1663db56199c5353592009e34aaa51078a2469bed068bb8d6f0ba43accf97
Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
30
Known Problems

Intermittent failure of a purge control valve in the evaporative emission system can cause the Check Engine Light to illuminate. A failed valve should be replaced to correct this problem.

 

Cars equipped with an automatic transmission might experience a hesitation when accelerating. Revised software for the on board computer is available which may correct this problem. Software revisions are commonly most helpful on newer vehicles. once the mileage builds up a worn component could cause similar problems. Whenever major transmission work in performed, the transmission software should be updated as necessary.

On higher mileage vehicles, an engine misfire may develop and/or the Check Engine Light may illuminate due to a failed ignition coil. It is not uncommon to replace all the coils when the first one fails in order to prevent return trips to the repair shop.

The valve cover gaskets have a tendency to leak oil, especially the one near the firewall.

The power steering pump and power steering hoses tend to develop leaks, particularly in the V6 models.

One or more motor mounts may wear out on cars with high mileage. This will put extra stress on the other mounts, and the faulty mount(s) should be replaced.

The Evaporative system may have problems with the vapor canister releasing charcoal pellets that plug the vent valve. Typically a Code P0441, P0442 and P0446 will be set. The key code is the P0446 which is a vent valve electrical failure. The proper repair is to replace the entire canister with all the valves as a unit. This is located on top of the fuel tank and is expensive. Our Technicians tell us that for awhile Toyota was covering these problems, but this may have changed. It would not hurt to call the dealer if this problem occurs to see if Toyota is still helping with these repairs.

The Check Engine Light may illuminate because a component of the oxygen sensor stops working. As a result the engine computer is unable to determine the proper ratio of air to fuel for the engine. Replacing the failed oxygen sensor should correct this concern.

At higher mileages, an anti-lock brake system wheel speed sensor may wear out and illuminate the ABS warning light. It is recommended to replace the sensor with a factory part and be sure to clean all rust and debris from the mounting area because the mounting distance is critical. Failure to do so may result in the new sensor setting false trouble codes. Be sure to check the condition and runout of the front wheel bearings on the 2WD and 4WD vehicles and the CV joints on the 4WD vehicles since worn wheel bearings and/or CV joints can cause the ABS trigger rings to rub against the ABS sensors and damage them.

At higher mileages, (125,000-150,000) the automatic transmission may not shift correctly. This can be caused by the throttle position sensor being out of adjustment or a shift solenoid needing to be replaced. Typically the transmission does not need to be completely overhauled.

The proper repair for a leaking Steering Rack & Pinion is replacement with a new unit.

At 125,000-150,000 miles, the Brake Master Cylinder may need replacing. When replacing the master cylinder, it is critical to adjust the brake pedal to master cylinder pushrod clearance or the brakes can drag and overheat.

The idle air control motors tend to become carboned up at around 100,000 miles and will cause a start and stall and/or stalling at stop sign problems. Many times these valves can be cleaned, however, the sure bet is to replace the idle air control motor and clean the throttle body.

On vehicles with a manual transmission, worn shift bushings can cause the transmission to pop out of gear, especially when coasting down in 1st or 2nd gear. Replacing all the shift linkage bushings is pretty straight forward and not expensive and will commonly correct this concern.

Over the time the exhaust gas recirculation (EGR) system may become plugged with debris, the oxygen sensor may also be getting slow or 'lazy' around this time. When servicing or cleaning  the EGR system, it is a good idea to replace the oxygen sensor because it works in tandem with the EGR system.