Close

Hyundai Tiburon Questions

Get answers to questions about your Hyundai Tiburon at RepairPal. Find solutions, diagnose problems and get back on the road.

Refine by vehicle
×
Choose your vehicle
No car image 94a1663db56199c5353592009e34aaa51078a2469bed068bb8d6f0ba43accf97
Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
295
questions

I replaced transmission in my car and now it will not start. The Fuel pump does not kick in and the coil pack has power but it seems as though no signal to fire. I thought it may be a security or shut off switch of some sort but can not find anything. My care did fall 2 time while on jack stands.

I changed out the transmission in my 99 gen 1 Tiburon with a transmission out of a gen 2 with the same motor did ask dealer if this would work. It fell two time while on jack stands while putting it back together now it will not start. It would start before transmission change. The fuel pump is not kicking on and the coil pack is getting power but not sending signal to fire.

Car run horrible. Sounds like a grinding noise

2003 GT V6 Automatic. Idles well in park, but when I am at a stop sign or stop light, it seems to "surge" and wants to go forward. I don't know if it is an engine surge thing, or a transmission thing. I don't notice any other problems with the engine, or with the transmission. Just this weird surging feeling when fully stopped. I've even checked to make sure the engine mounts seem tight, just to be sure it wasn't some type of "slipping" because of that. No codes are being thrown. I currently just put the car in Neutral and wait for the light to change. No "surging" in Neutral, either. Any thoughts or suggestions?

What causes this, do I need a new transmission or am I able to fix this

They come and go,mostly don't turn on,only every once and awhile

Does it need ,motor work

hit a guard rail, bent frame on front drivers side. need any and all info you can possibly give me, can show pics if needed

I have a 2005 Hyundai Tiburon that needs an air conditioner. I'd like to 1) find a local mechanic, 2) get a rough estimate on parts, and 3) a rough estimate on labor. Thanks

Power steering fluid leak

no codes all monitors run except catalyst what should we do next

Misfire or vibration only during acceleration. What would cause this at only higher speeds

Cam sensor, crank sensor, coil pack,plugs plug wires,I am at a loss. Someone help please.

car drove fine all day - cluch got hard and soft. Fluid levels are okay

I also replaced plugs and wires it bubbles up and runs hot. Why?

Car was running fine a month ago. Installed a new air intake filter, yesterday. Cleaned car, including spraying some water under the hood, which may have affected something. Started car, idled very well, put in gear, applied gas, released clutch...car coughs and sputters, then dies. Multiple attempts, no go.

At first the engine would rev high so I would shut it off and restart then would put in reverse and it wouldn't move or engage until giving it gas. Can you tell me what the problem is? Not sure if it needs a new tranny or if its and idle sensor. Mechanic said it doesn't have a vacuum leak. The problem seems to happen after I've driven it for awhile

in cold weather it seems to werk fine i went to idahoe and salt lake this last winter and it ran fine i could shut it off restart drive slow fast no problems over 2000 miles and about a week when i got back down to arizona it started acting up again. it had this problem b 4 i went but new about the cold weather thing so i thought i try it its been sitting ever since its no fun to drive when it wont rev past 3000 thanks kidad

This is what guy wrote word for word. "selling it for is a very honest guy very rare now a days lol. The car has a bent valve causing it to not have any compression to the cylinders 1, 2, and 5". Can you tell me if this is work I can do fairly easy, and what something like this would cost. Pros and cons.

Can I have the oil pan rethreaded or tapped out instead of buying a new one.

When I try to leave in first it grinds and hops out but not in anyother gear

cud it be bcm?

i replaced bearing 1 yr back checked its still good i hope transmission is ok how can i know if cv joint is bad and not the transmission or axle to

the noise happens only upon acceleration and around 3RPM - 4 RPM's we just replaced the clutch and transmission engine appeared intake running fine. Please help if you know what we should be looking for.