Close

2005 GMC Sierra 2500 HD Problems

RepairPal has identified the most common problems with the 2005 GMC Sierra 2500 HD based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

No car image 94a1663db56199c5353592009e34aaa51078a2469bed068bb8d6f0ba43accf97
Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
19
Known Problems

One or more heater & AC (HVAC) temperature and/or air delivery mode door actuator may fail, resulting in improper temperature or air delivery. If this occurs, fault code(s) should be stored in the HVAC control module which should assist in diagnoses.

The 4WD transfer case encoder motor position sensor or the selector switch may fail causing the service 4WD message to be displayed. Fault code(s) stored in the transfer case control module will be of assistance in determining the exact fault causing the message to be displayed.

The muffler heat shield may become loose on the muffler causing a rattle or popping noise. Our technicians tell us there is a kit available from GM to correct this problem.

The daytime running lights are prone to burning out. Our technicians tell us that the light sockets may show signs of heat damage but usually are OK. Always be sure to use the correct replacement bulb for the best life expectancy. The new bulb recommendation for 2001-2003 models is #4114K (trade number).

A poor electrical ground under the battery tray may cause the ABS warning light to illuminate. Our technicians tell us that cleaning and properly securing this ground and also the main ABS ground on the frame rail below the drivers door may be necessary.

Units with 4 wheel disk brakes may develop at situation where the park brake does not hold as it should. Our technicians tell us this can be caused by worn park brake shoes located inside the drum section of the rear brake disks. The worn shoes should be replaced and properly adjusted to correct this issue.

A clicking noise may be noted from the turn signal flasher after the turn signals are switched off.  This is commonly cause by a faulty turn signal switch which will require replacement.

The speedometer or other instrument panel gauge may begin to work erratically at times. Our technicians tell us that the instrument cluster must be sent to a repair facility to correct this fault. The warranty has been extended on some of these units to 7 years or 70,000 miles.

The fuel pump may fail causing the engine to stall and not restart.

The headlight switch used on the GMC Sierra 2500 HD is known to fail through normal operation. Since the headlight switch is also integrated into the interior lights, a malfunctioning switch can cause issues with interior lights as well.

  • Symptoms of a failed headlight switch include:
  • Headlights and taillights failing to turn on or off
  • Interior lights flicker, or fail to turn on or off
  • Gauge cluster lighting off or flickering with headlights on
  • Parking light malfunctions  

This issue is well known with General Motors Trucks and SUVs, and is solved by testing and, if needed, replacing the headlight/dimmer switch. Bad grounding wires at the tail-lights, and dirty/corroded tow package wires can also lead to some of these issues. 

A dirty throttle body may cause a lower than normal idle and possible stalling condition. Performing a throttle body service will commonly correct this concern.

The 2004-2007 GMC Sierra 2500 HD is known to have issues with the EVAP system, a part of your emission control system.

The EVAP canister vent valve or valve solenoid wiring may fail causing illumination of the check engine light, setting code P0446, and problems filling the tank with fuel.

To correct the issue, the EVAP canister vent valve, solenoid, and wiring must be inspected. The most common fix is replacement of the wiring connector or replacement of the vent valve assembly.

One or both secondary air injection check valves may become restricted causing poor air flow resulting in illumination of the Check Engine Light. It is often recommend to replace both check valves even if a fault code is set for only one bank of cylinders. Replacing only one valve may result in a return trip to the repair shop.

Illumination of the Check Engine Light can be caused by a loose or worn gas cap.