Close

2010 Ford Mustang GT Problems

RepairPal has identified the most common problems with the 2010 Ford Mustang GT based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
8
Known Problems

The Ford Mustang GT from 1996-2010 is known for displaying the normal symptoms of a coolant leak, including overheating, especially when the vehicle is idling, the strong smell of coolant from the engine, and illumination of the low engine coolant warning light

This leak is difficult to locate as it is buried underneath the intake manifold, and only begins to leak coolant onto the ground in advanced stages of disrepair. This leak springs from the heater tube, which allows coolant to flow between the water pump and HVAC heater core

When the connection for this tube begins to leak, the coolant burns on the hot engine, and produces a sweet smell that is unmistakably engine coolant. 

The remedy can be complicated, and will necessitate removal of the intake manifold, heater tube, and possibly the water pump. After removal of these items, the connector may be replaced, or a set of o-rings, depending on the year of the vehicle. Most vehicles, model 2002 and later, will have o-rings, and the water pump will not need to be removed. 

The Ford Mustang GT is known for intermittent rough idling, which may be accompanied by illumination of the check engine light, and poor fuel mileage.

This may be caused by the EGR sensor sticking, causing the EGR valve to stay slightly open, and diagnostic testing must be conducted.

The EGR valve and sensor must be replaced together to correct this concern.

 

The Ford Mustang GT is known for idling roughly, with a slight whistling noise from the engine compartment. After a short time, this may result in poor fuel mileage, and illumination of the check engine light

This is caused by a cracked positive crankcase ventilation (PCV) valve hose, which allows a small vacuum leak, and improper evacuation of engine crankcase pressure.

Correction is simple, and requires replacement of the PCV hose. An updated part may be available. 

Drivers may notice the engine idling roughly, hesitation to accelerate, and even engine stalling on the Ford Mustang GT V8..

The mass air flow sensor (MAF) is prone to fail, and commonly is diagnosed as the faulty component when these issues arise.

When the Check Engine Light illuminates, and the diagnosis is a failed MAF, it will require replacement to correct the issue. 

Ensuring the air filter is installed properly, and sealed to the air filter housing, can help prevent MAF sensor issues. 

The 2010-2014 Ford Mustang GT with automatic climate control may have a problem with frequent fan speed changes when using the heater or air conditioner. This includes all performance models including the GT500, BOSS 302, GT, GT350, GT-H, and CA Special Ed.

Normally, the fan speed changes only to maintain a selected temperature, but when the fan speed changes frequently and needlessly, there is an issue with the fan speed control unit. 

The fan speed control unit, sometimes erroneously called the blower motor resister, regulates the speed for the blower motor in order to maintain the temperature set by the driver. When it fails, the fan will run at random settings, and the climate control will be inaccurate.

Note: this does not affect the temperature of the air that comes from the vents, it affects the amount of air that comes from the vents. 

The repair is simple, and quick. The control unit is located behind the glove box in most models, and removal and installation takes only minutes.

Also note: this only applies to vehicles with single or dual automatic climate control.

If a squeaking noise is heard while turning the steering wheel, the outer tie rod ends may be worn and should be replaced.

4.0L V6 engines may develop a buzzing type noise from the upper engine area at about 1900 RPM, under light acceleration. Our technicians tell us this can be caused by loose ignition coil bracket bolts. Coil bracket bolts should be checked for the correct torque before further diagnoses is performed.

Internal heater blower motor issues can cause a ticking noise from the heater blower when the fan is on. To correct this concern, replace the heater blower motor with a revised unit.