PensFan

Rookie
45 points
Recent Activity

Question Asked: Engine Cradle
October 11, 2010, 03:44 AM
I found out the popping noise I have been hearing is the engine cradles both sides front and back need replaced.Frame seems fine, 2 in front and 4 in back.The 2 the farthest back are completely gone.No bushing in them at all. Are the other 4 sufficient at this point? I hate to put a lot of money in it. The other 4 look pretty good.Any idea on what I should expect the cost to fix this problem to be?
Question Asked: Loose vacuum line and transmission not shifting properly
January 13, 2010, 08:41 AM
Transmission shifts funny from 35-55 if under a slight load. Shifts fine if not under a load and seems to shift ok too if I'm rapidly gaining speed opposed to gradual speed gain.It would jump back and forth when trying to upshift, if I tried to gain speed it evenually shifts up ok and runs fine. Gotten more pronounced the past week or so. It is fine at slower speeds even climbing a steep street. I'm really hoping this is not serious. I put 1/2 qt of fluid in it because it was low but did not help. Could it be a modulator? No engine light on or other lights. Seems not to happe I did try putting a pencil in a loose vacuum line but the car shifted even worse then throughout the whole shifting range. Thanks Very Much
Question Asked: Transmission jerking when shifting
January 11, 2010, 03:54 PM
Transmission shifts funny from 35-55 if under a slight load. Shifts fine if not under a load and seems to shift ok too if I'm rapidly gaining speed opposed to gradual speed gain.It would jump back and forth when trying to upshift, if I tried to gain speed it evenually shifts up ok and runs fine. Gotten more pronounced the past week or so. It is fine at slower speeds even climbing a steep street. I'm really hoping this is not serious. I put 1/2 qt of fluid in it because it was low but did not help. Could it be a modulator? No engine light on or other lights. Seems not to happens so much when it's cold.
Question Asked: Vacuum hose is off under hood, bilevel not working
January 11, 2010, 03:44 PM
A/C and heater both blow fine upper and lower but neither will blow thru bi-level. I checked under the hood under the black plastic box by the firewll. There was a split tube with one small vacuum line disconnected. Not sure where it connects to though. It appears to have been taken out of the bundle of tubes in the split plastic tube but not sure why. Any help is appreciated. Thanks Very Much
Question Asked: Transmission shifting oddly
January 03, 2010, 04:49 PM
I'm not sure if it's slipping or just plain not shifting properly. Started about a month ago at about 45-55mph. It would jump back and forth when trying to upshift, if I tried to gain speed it evenually shifts up ok and runs fine. Gotten more pronounced the past week or so. From about 35-50 if I'm on a slight grade then it does it. If not it shifts fine and it's fine as slower speeds even climbing a steep street. I'm really hoping this is not serious. I put 1/2 qt of fluid in it because it was low but did not help. Could it be a faulty speed sensor? Anyone who checks this out and responds I really appreciate it. I forgot to add, it appears if I shift to D3 it shifts ok if that helps.
Question Asked: A/C works, blows thru defroster and lower but not bi-level
December 28, 2009, 03:50 PM
A/C and heater both blow fine upper and lower but neither will blow thru bi-level. Is this a fuse, vacuum hose or what? If it's a hose where would it be and would it be disconnected or something else? Would it be under dash or in engine compartment? Thanks Very Much Bill
Question Asked: Turn signals won't flash even after chging bulbs
December 28, 2009, 03:46 PM
What else would be the most likely cause of the problem, a fuse or the relay? If it's the relay is there one for each side or just one for both? Where is(are) is located? Thanks Very Much Bill
No activities found
No activities found
No activities found
Answer Ranks