1992 Toyota Land Cruiser Problems

RepairPal has identified the most common problems with the 1992 Toyota Land Cruiser as reported by actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

Refine by vehicle
Choose your vehicle
Known Problems

The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and the EGR Temperature sensor. Our technicians tell this repair is pretty straight forward and takes about 1-1.5 hours. It is also wise to verify the EGR system components i.e. the Transducer, EGR Valve and VSV Solenoid at this time.

The anti-lock brake system (ABS) may function erratically or illuminate the warning light due a damaged wheel speed sensor. A wheel bearing and/or CV joint with excessive runout can cause the ABS trigger rings to rub against the ABS sensors and damage them.

At higher mileages, (125,000-150,000) the automatic transmission may not shift correctly. This can be caused by the throttle position sensor being out of adjustment or a shift solenoid needing to be replaced. Typically the transmission does not need to be completely overhauled.

The AC Expansion Valve may develop a very slow leak or allow too much refrigerant flow which reduces cooling. Our technicians tell us that Toyota makes an updated expansion valve to resolve these problems if and when they occur.

The Throttle Position Sensor can get out of adjustment due to wear in the throttle body or due to carbon build up. This will cause the idle timing to advance more than 30 degrees which will cause very high HC and NOx emissions. Conversely, the Throttle Position Sensors can wear out and not properly advance the timing which causes a lack of power and poor fuel economy.

Typically the AC compressor is worn out by about 150,000 miles in warm and/or humid climates. It is recommended to replace the complete compressor including a new clutch and rpm sensor, and to replace the receiver/dryer as well.

At higher mileages, an anti-lock brake system wheel speed sensor may wear out and illuminate the ABS warning light. It is recommended to replace the sensor with a factory part and be sure to clean all rust and debris from the mounting area because the mounting distance is critical. Failure to do so may result in the new sensor setting false trouble codes.

If the vehicle will not crank over, the most common problem is the starter, which tend to fail at about 100,00-125,000 miles. Sometimes it is only the starter solenoid contacts, but often the complete starter (including solenoid) needs to be replaced.

We recommend flushing the brake fluid every 60,000 miles because the fluid can become dirty and may cause problems in the brake system such as premature failure of the master cylinder or wheel cylinders.

It is important to regularly check the valve clearance as the exhaust valves may become too tight. This will lead to valve failures, which are expensive to repair.

Our technicians report that by 100,000 miles, the ignition key tends to wear out and should be replaced or it may not work as well in the door locks or ignition lock cylinder.

Over the time the exhaust gas recirculation (EGR) system may become plugged with debris, the oxygen sensor may also be getting slow or 'lazy' around this time. When servicing or cleaning  the EGR system, it is a good idea to replace the oxygen sensor because it works in tandem with the EGR system.

At higher mileages (125,000+) the mass air flow sensor may cause the vehicle to idle rough, run rich and even stall. Our technicians recommended to replace the Mass Air Flow Sensor with a factory unit because the aftermarket units have very mixed results.

At higher mileages (125,000+) the Engine Coolant Temperature Sensor may intermittently stop working, especially when the vehicle is fully warmed up. This can cause the engine to stall unexpectedly.

A rough idle and even an emissions inspection failure for high HC and CO can be caused by improperly adjusted valves. Also, exhaust valves may become to tight which can lead to valve failures. Our technicians tell us that regular valve adjustment inspections are a must.