After much investigation of temp sender, fuel injectors, and ignition parts, the problem was traced to the ECU. On replacement, the problem was fixed.
Problems for specific Toyota Camry years:
Car problem reports
Problem with your car? See what our experts say or submit your own.
Newest reported 1995 Toyota Camry problems
At higher mileages, an anti-lock brake system wheel speed sensor may wear out and illuminate the ABS warning light. It is recommended to replace the sensor with a factory part and be sure to clean all rust and debris from the mounting area because the mounting distance is critical. Failure to do so may result in the new sensor setting false trouble codes. Be sure to check the condition and runout of the front wheel bearings on the 2WD and 4WD vehicles and the CV joints on the 4WD vehicles since worn wheel bearings and/or CV joints can cause the ABS trigger rings to rub against the ABS sensors and damage them.
The Check Engine Light may illuminate with code P0770 and/or P0773 stored. This would indicate a fault with the 3-way lock-up solenoid which could be defective and may need replacement.
The valve cover gaskets have a tendency to leak oil, especially the one near the firewall.
The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and the EGR Temperature sensor. Our technicians tell this repair is pretty straight forward and takes about 1-1.5 hours. It is also wise to verify the EGR system components i.e. the Transducer, EGR Valve and VSV Solenoid at this time.
If the vehicle will not crank over, the most common problem is the starter, which tend to fail at about 100,00-125,000 miles. Sometimes it is only the starter solenoid contacts, but often the complete starter (including solenoid) needs to be replaced.
On vehicles with a manual transmission, worn shift bushings can cause the transmission to pop out of gear, especially when coasting down in 1st or 2nd gear. Replacing all the shift linkage bushings is pretty straight forward and not expensive and will commonly correct this concern.
The pickup coil inside the distributor can fail and cause a no-start condition. There have also been some failures of the radio noise suppressors inside the distributor which can short out. It is recommended to replace the whole distributor with a complete genuine Toyota distributor if any of its components fail.
After much research and replacing all the motor & transmission mounts I discovered the solution. "Exhaust Hanger Replacement." Wait till you see what Toyota is charging for these little babies. Essentially there are 5 hangers. Front, mid and front muffler hangers are all permanently attached to spindles and a small metal hanging chassis. Replacement is easy and can be done with just a socket wrench. The local dealer here charges $63 a piece (w...
A loss of power on the freeway may due to an internally leaking fuel pulsation dampener. This commonly occurs on higher mileage vehicles.
The ignition coil inside the distributor may fail. Our technicians tell us this may result in a hesitation on acceleration, especially when the vehicle is warming up on cold, rainy days. The pickup coils inside the distributor can also fail and cause a no-start condition. There have also been some failures of the radio noise suppressors inside the distributors, which can short out. Our technicians recommend replacing the whole distributor with a complete, genuine Toyota distributor if any of its components fail.
The head gaskets are prone to leaks in as little as 60,000 miles. When the head gasket is replaced, the knock sensor harness should be replaced as well, as it can be damaged by leaky head gaskets, resulting in a serious decrease in fuel efficiency or in long term engine damage.
At 125,000-150,000 miles, the Brake Master Cylinder may need replacing. When replacing the master cylinder, it is critical to adjust the brake pedal to master cylinder pushrod clearance or the brakes can drag and overheat.
A rough idle and even an emissions inspection failure for high HC and CO can be caused by improperly adjusted valves. Also, exhaust valves may become to tight which can lead to valve failures. Our technicians tell us that regular valve adjustment inspections are a must.