1995 Toyota Avalon Problems
RepairPal has identified the most common problems with the 1995 Toyota Avalon as reported by actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.Refine by vehicle
The motor for the rear window sunshade in the Toyota Avalon is known to fail. When this occurs, the sunshade will not extend down the window, and a grinding noise is heard until the motor fails as well.
Replacement of the sunshade assembly is necessary to correct this failure, however, removing the fuse for the sunshade will stop the motor from making the irritating grinding noise.
Debris can get into the idle air control valve. This will restrict the air flow into the engine, causing idle speed and/or stalling when cold. The valve can be cleaned or replaced to correct this concern.
Sludge can build up in the engine because Toyota did not recommend frequent enough oil changes. Lexus will sometimes offer a discount on cleaning the engine if necessary. Owners who changed their oil every 3,000 miles did not experience these problems. This sludge build up can lead to excessive oil consumption.
The Toyota Avalon with the 3.0L V6 engine has a known issue with the valves that if left unchecked, will cause burned valves and engine performance issues.
The engine ‘breathes’ through valves that are pushed open by the camshaft, and closed by springs. When valves are closed, they seal against a valve seat. In this vehicle, the valve seat is too soft, so after the valve contacts it thousands of times, it becomes crushed. Once it is crushed, the valve can no longer make a proper seal, and the valves erode due to extreme temperature (burnt valve).
Symptoms related to this issue:
- Rough idle
- Backfiring through exhaust or intake
- Illumination of the check engine light
- OBD Trouble Codes P0300, P0301, P0302, P0303, P0304
- Loss of power
- Engine Stalling
To repair the burnt valves, the cylinder head must be removed and rebuilt, which is a costly internal engine repair, however, this issue can be prevented through inspection and adjustment of valve clearances every 40,000 miles.
At 125,000-150,000 miles, the Brake Master Cylinder may need replacing. When replacing the master cylinder, it is critical to adjust the brake pedal to master cylinder pushrod clearance or the brakes can drag and overheat.
A loss of power on the freeway may due to an internally leaking fuel pulsation dampener. This commonly occurs on higher mileage vehicles.
The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and the EGR Temperature sensor. Our technicians tell this repair is pretty straight forward and takes about 1-1.5 hours. It is also wise to verify the EGR system components i.e. the Transducer, EGR Valve and VSV Solenoid at this time.
The engine mount on the passenger side of the car can wear out on cars with high mileage. This will put extra stress on the other mounts and the faulty mount will need to be replaced.
The Evaporative system may have problems with the vapor canister releasing charcoal pellets that plug the vent valve. Typically a Code P0441, P0442 and P0446 will be set. The key code is the P0446 which is a vent valve electrical failure. The proper repair is to replace the entire canister with all the valves as a unit. This is located on top of the fuel tank and is expensive. Our Technicians tell us that for awhile Toyota was covering these problems, but this may have changed. It would not hurt to call the dealer if this problem occurs to see if Toyota is still helping with these repairs.
As the size of the Camry vehicle gets ever larger, there is a tendency to warp the front rotors. This will be felt as a shudder in the steering wheel when braking. The front rotors can be remachined, if there is sufficient material left, other wise the front rotors will need to be replaced. It is recommended to use factory quality rotors because cheap quality rotors warp very easily and tend to squeak and squeal.
A rough idle and even an emissions inspection failure for high HC and CO can be caused by improperly adjusted valves. Also, exhaust valves may become to tight which can lead to valve failures. Our technicians tell us that regular valve adjustment inspections are a must.