1992 Toyota 4Runner Problem Reports

Newest 1992 Toyota 4Runner Problem Reports

Report A Problem

At higher mileages, an anti-lock brake system wheel speed sensor may wear out and illuminate the ABS warning light. It is recommended to replace the sensor with a factory part and be sure to clean all rust and debris from the mounting area because the mounting distance is critical. Failure to do so may result in the new sensor setting false trouble codes. Be sure to check the condition and runout of the front wheel bearings on the 2WD and 4WD vehicles and the CV joints on the 4WD vehicles since worn wheel bearings and/or CV joints can cause the ABS trigger rings to rub against the ABS sensors and damage them.

The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and the EGR Temperature sensor. Our technicians tell this repair is pretty straight forward and takes about 1-1.5 hours. It is also wise to verify the EGR system components i.e. the Transducer, EGR Valve and VSV Solenoid at this time.

At higher mileages (125,00+) the Engine Coolant Temperature Sensor may intermittently stop working, especially when the vehicle is fully warmed up. This can result in illumination of the Check Engine Light and/or an engine stalling problem.

On vehicles with a manual transmission, worn shift bushings can cause the transmission to pop out of gear, especially when coasting down in 1st or 2nd gear. Replacing all the shift linkage bushings is pretty straight forward and not expensive and will commonly correct this concern.

On the 4 Cylinder Engines, the Ignition Coil wire insulation is often rubbed through by the Primary wiring harness which will cause a stalling/no-start condition. The coil wire will need to be replaced and the primary harness will need to be repaired and re-routed.

At higher mileages (125,000-150,000) the input shaft seal to the power steering gear may leak. It is recommended to replace the steering gear with a quality rebuilt or new unit rather than attempt to re-seal the original unit.

A loss of power on the freeway may due to an internally leaking fuel pulsation dampener. This commonly occurs on higher mileage vehicles.

The timing chain can develop a rattling noise caused by failing timing chain guides. This is often due to extended mileage intervals between oil changes that allows the oil to become dirty and abrasive which wears away the timing chain guides until they fail. The timing chain and guides should be inspected at each valve adjustment, otherwise serious engine damage may result.

The 3.0 V6 engine is usually prone to leaks in the head gasket after as little as 60,000 miles. When the head gasket is replaced, the knock sensor harness should be replaced as well, as it can be damaged by leaky head gaskets, resulting in a serious decrease in fuel efficiency or in long term engine damage.

Typically the AC compressor is worn out by about 150,000 miles in warm and/or humid climates. It is recommended to replace the complete compressor including a new clutch and rpm sensor, and to replace the receiver/dryer as well.

Usually by 150,000 miles the AC system will need some attention, especially in climates where it is used often. Our technicians tell us that it is best to service the AC system every 2-3 years. This keeps the moisture in the system at a minimum which extends the life of the components.

The AC Expansion Valve may develop a very slow leak or allow too much refrigerant flow which reduces cooling. Our technicians tell us that Toyota makes an updated expansion valve to resolve these problems if and when they occur.

A rough idle and even an emissions inspection failure for high HC and CO can be caused by improperly adjusted valves. Also, exhaust valves may become to tight which can lead to valve failures. Our technicians tell us that regular valve adjustment inspections are a must.

Over the time the exhaust gas recirculation (EGR) system may become plugged with debris, the oxygen sensor may also be getting slow or 'lazy' around this time. When servicing or cleaning  the EGR system, it is a good idea to replace the oxygen sensor because it works in tandem with the EGR system.

Front brake rotors can wear causing a pulsation felt in the brake pedal. Our technicians tell us this condition is best corrected by replacement of the front rotors and brake pads.