Mazda B2200 Questions
Answered Mazda B2200 Questions
Ask a Question
I have a Mazda B2600 2.6L 5 speed manual transmission. Why does is keep burning out the mass flow sensor? What can I do to remedy this problem?
On the intake side of the heater core had broke where the hose connects to intake any suggestions on what could be done to repair this? Any suggestions would be greatly appreciated thank you for your time.
it happens when it warms up ichecked every thing i could think pleas help its making me nuts
what compressor can I use, is there a factory bracket. what do I need to know. Thanks
I just fixed my truck from having a blowed head gasket
Having to change oil pan gasket which is the easiest way I was told drop sway bar than told not to. have to lift motor up 2 inches
I've put a new alternator on it and a new battery. And when you start it up, it'll only run 30min-1hr. Then just dies because the battery is drained down.
I found a vacuum line that's leaking oil, on the drivers side of the transmission. Could that be the problem?
this happens whenever i have to stop such as at a redlight etc...
clutch on a 1988 Mazda B2200 truck does not pop back up once it is pushed.
on 25/25 test HC PP Reading 505 allowed is 223 Co% Reading 12.22 allowed is 2.79 On 50/15 test HC Pp Reading is 389 allowed is 228 Co% reading is 11.86 allowed is 2.06 Can you t...
after i put trans back on the clutch pedal when foot off it wont come back up it'll stay down.already replaced slave tried bleeding but still stays down what could it be?
I would like to change the cylinder head gasket and I need a diagram on how to do it and I could not find my book.
The old O2 sensor didnot give me check engine light.But the new one did it twice then turns off when I park re-star my truck again. Any advice what can I do ??? A friend of mine told me BOSCH works better with europea...
Truck was running fine tell I redid all the front gaskets than developed a tick in the head had it running with the valve cover off to see what was going on and head is only reciving oil in the rear of the head and no...
The first smog test became bad,but most of the error were fixed.Today got the second smog test,everything passed,but FAIL-ECS: other emission related components. Then the technitian wrote at the bottom of the results...
put a ground wire from the green test connector.Set the rpm to 750 on idle and timing on 6. As soon I disconnect the ground wire,the engine accelerate and rpm goes over 800.The repair manual ask me to ground the test ...
Any idea how to solve the problem??? Already replaced pcv valve.Bought new gas tank cap. Any idea this will fix the problem ?
what should I do to fix this ??
just bypass the heater core cause a leak inside the truck
is it worth it ? or not ?
even trying hard just stays in the ACC position
how can i make sure i installed it the right way?
If you can only stop your truck by pumping the brake peddle three to four times, does that indicate that the ASB hydraulic valve assembly is not working? Just had all the brake parts that were rubber replaced, front b...
brake fluid that brake system was filled with power steering fluid when having a oil change. brkae system was contamied and had to replace all rubber basied compontes due to the fact it caused all rubber oarts to swel...
when remove fuel from arrow side of filter, filter will fill from 1/3 to full.
the truck is really hard to start up in the morining mostly have to push the gas pedle all the way to the floor to get it started. while started the rmp idles to 2500 rpm.
Issue occurs in 1st and 2nd gear, where the grabbing or stuttering action happens upon releasing clutch. Have had slave cylinder replaced approximately 2 years ago; cracked manifold replaced 1 year ago. 135,000 mi. ...
it's really hard to turn.it just had new ball joints put on,and that wasn't the problem.what could it be?