Chevrolet Beretta Questions

Answered Chevrolet Beretta Questions

Ask a Question
View:RecentAnsweredUnanswered
They had a rebuild starter put in and it started fine for awhile. Now it doesn't start again so they took the starter out and took it back to Advanced Auto and they tested it and said it was fine. Could there be a d...
out but that use also operates my rear view mirror lights
Replaced water pump. Jist cant find bleeder screw
It will start and run great till it hits about the half mark on the temp gauge then it dies and won't start up again till the next morning I've replaced the icm ecm crank shaft sensor fuel pump coil packs battery. No ...
the heat only comes out the vent and floor and will not switch to another location on the control panel
when turn the key it is in between lock and start position will not return to lock position and will not start car
what type of wrench do i need to remove the lower control arm bushings from the car ?
My Beretta is equipped with a 3.1L. The engine fan does worn with the AC on. Where is the temp sensor located on this vehicle? There should be one for the gauge and one for triggering the fan when it reaches a certain...
I have fuel comin back the return line, but not starting. If i dump gas in the carb, it will start and run til that runs out. Im assuming something with injectors or a relayfor one, but i dont kno anything about that ...
i check the battery but the ligt service engine soon dont come on when i try to start the car could be the ecm?
radiator cracked fixed it drove it but it kept getting hot than cold cause of thermastate. now it wont start it cranks over but it over flows out of resivore while trying to start what is the problem
i replaced the ignition switch, swapped batterys, tested the starter, and checked all fuses. nothing happens. when i go to "start" the car... nothing. all you hear is the fuel injectors. no sound from the starter at a...
and i checked the fuel pump relays an all my wires and it will only start off of starting fluid then die after
Has high mileage,did change fuel filter.
Coolant system was just drained and reserviced. The coolant low level light will not go out. The sending unit appears to be an internal part of the reservior. Do I need a new reservior?
Removed drum and inspected shoes, inside of drum shows very little wear and both shoes are wearing evenly. All appears normal. But, problem occurs with every application of brakes forward or reverse.
The car will turn over and idle for like 30 seconds and then shut off. It also shuts off immediately when you touch the gas. I have replaced the crankshaft sensor, fuel filter, vacuum lines, spark plugs, wires, oil ch...
i change the colant sensor and checked the fuses on the driverside both ae good. what is left to check?
Took the car 2the shop 2get the check engine light looked at. The OBD-I, scanner says its the EGR SOLENOID. Is that the EGR valve or is it referring 2the CANISTER PURGE VALVE SOLENOID? The mechanic pointed 2the EGR v...
I just replaced the crank position sensor. 2.2 4 cyl still wont start. turns over good - gas is coming out from throttle body fine - nice little mist - but no spark or sometimes a backfire type sound as its turning o...
how do u replace the whole unit i just bought a new assembly but where do i start!!!!!
I'm sure I need to replace the crankshaft position sensor/modul on my 1991 4 cylinder 2.2 beretta. I was told I may need to drop the oil pan to pry it out from the inside!! IS my neighbor just trying to scare me? I...
My car will go in Drive,but not reverse or Neutral. I was told to check transmission fluid. Where is the cap located? or any other suggestions?
car started running rough and burned the gas at about three times the normal rate.Changed plugs and wires now it will start but runs terrible,and only runs for a second and if you give it gas it dies immediatly.
hard starting cold with fresh gas starts good warm runs ruff with no power after warm is a 2.2 Engine 96 Beretta
My 1994 bretta electric window stoped about 3/4 the way now won't go up or down
I have a 1989 chevrolet/beretta/2.8L. How much time/work to replace belt tensioner. Do I have to loosen motor mount to access the tensioner, for there’s no room there.