Toyota T100 Problem Reports

Newest Toyota T100 Problem Reports

Report A Problem

At higher mileages, an anti-lock brake system wheel speed sensor may wear out and illuminate the ABS warning light. It is recommended to replace the sensor with a factory part and be sure to clean all rust and debris from the mounting area because the mounting distance is critical. Failure to do so may result in the new sensor setting false trouble codes. Be sure to check the condition and runout of the front wheel bearings on the 2WD and 4WD vehicles and the CV joints on the 4WD vehicles since worn wheel bearings and/or CV joints can cause the ABS trigger rings to rub against the ABS sensors and damage them.

Some engines have had the problem of the crankshaft pulley bolt coming loose. This will make a rattling noise as the engine idles. Our technicians tell us that the pulley bolt should have a thread locker applied and then retorqued.

The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and the EGR Temperature sensor. Our technicians tell this repair is pretty straight forward and takes about 1-1.5 hours. It is also wise to verify the EGR system components i.e. the Transducer, EGR Valve and VSV Solenoid at this time.

At higher mileages (125,00+) the Engine Coolant Temperature Sensor may intermittently stop working, especially when the vehicle is fully warmed up. This can result in illumination of the Check Engine Light and/or an engine stalling problem.

Occasionally, the mass air flow sensor can go lean and set a code P0170 for fuel system lean. This in not an oxygen sensor problem. If there are no vacuum leaks, the mass air flow sensor may need to be replaced. Our technicians remind us to use a factory part because the aftermarket rebuilds are very inconsistent.

At higher mileages (125,000+) the mass air flow sensor may cause the vehicle to idle rough, run rich and even stall. Our technicians recommended to replace the Mass Air Flow Sensor with a factory unit because the aftermarket units have very mixed results.

If the vehicle will not crank over, the most common problem is the starter, which tend to fail at about 100,00-125,000 miles. Sometimes it is only the starter solenoid contacts, but often the complete starter (including solenoid) needs to be replaced.

On vehicles with a manual transmission, worn shift bushings can cause the transmission to pop out of gear, especially when coasting down in 1st or 2nd gear. Replacing all the shift linkage bushings is pretty straight forward and not expensive and will commonly correct this concern.

At higher mileages (125,000-150,000) the input shaft seal to the power steering gear may leak. It is recommended to replace the steering gear with a quality rebuilt or new unit rather than attempt to re-seal the original unit.

A loss of power on the freeway may due to an internally leaking fuel pulsation dampener. This commonly occurs on higher mileage vehicles.

The head gaskets are prone to leaks in as little as 60,000 miles. When the head gasket is replaced, the knock sensor harness should be replaced as well, as it can be damaged by leaky head gaskets, resulting in a serious decrease in fuel efficiency or in long term engine damage.

Typically the AC compressor is worn out by about 150,000 miles in warm and/or humid climates. It is recommended to replace the complete compressor including a new clutch and rpm sensor, and to replace the receiver/dryer as well.

Usually by 150,000 miles the AC system will need some attention, especially in climates where it is used often. Our technicians tell us that it is best to service the AC system every 2-3 years. This keeps the moisture in the system at a minimum which extends the life of the components.

The AC Expansion Valve may develop a very slow leak or allow too much refrigerant flow which reduces cooling. Our technicians tell us that Toyota makes an updated expansion valve to resolve these problems if and when they occur.

A rough idle and even an emissions inspection failure for high HC and CO can be caused by improperly adjusted valves. Also, exhaust valves may become to tight which can lead to valve failures. Our technicians tell us that regular valve adjustment inspections are a must.