Close

Audi Problems

RepairPal has identified the most common problems for 40 Audi models based on complaints from actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

No car image 94a1663db56199c5353592009e34aaa51078a2469bed068bb8d6f0ba43accf97
Get a Repair Estimate
Guaranteed by certified locations nationwide. Learn more
RepairPal estimates are guaranteed at over 1,700 quality certified locations nationwide. Learn more
244
Known Problems

A problem with the torque converter can cause the Check Engine Light to illuminate.

Erratic turn signal operation can be a result of a failing turn signal flasher relay which will require replacement.

Clogged drains can allow rainwater to accumulate in the plenum tray (at the base of the windshield). The water may leak into the vehicle's interior, brake booster, or electrical components, which can lead to major problems. Our technicians recommend keeping the tray clear of leaves, pine needles, and other debris.

The 2006-2016 Audi A4 Quattro uses FSI and TFSI direct injection engines. These engines are subject to carbon buildup in the intake system which can cause power loss, OBD codes and a check engine light, and a rough idle. In normal engines, the engine is cleaned by the gasoline flowing through the injectors and into the intake system, however, since the A4 Quattro uses direct injection, gasoline does not flow through common carbon buildup areas. 

Possible trouble codes include: P0300P0301P0302P0303P0304, P0305, P0306.

The solution is to remove the intake manifold and professionally clean the intake manifold, intake ports on the cylinder head, and the intake valves. This may need to be done in as few as 20,000 miles.

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision.