Audi Problems

RepairPal has identified the most common problems with the Audi as reported by actual vehicle owners. We'll tell you what the problem is and what it'll take to fix it.

Refine by vehicle
×
Choose your vehicle
244
Known Problems

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminatesT
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

Popping sounds from the rear of the vehicle may be heard moments after starting the engine, or when slowing to a stop. This noise is from the leak detection pump filling the fuel tank with air, and releasing to retest the system when it finds a fault. The sequence of faults identifying this issue are as follows:

  • Succession of loud pops from rear of vehicle
  • Pops go away, and fuel economy decreases 
  • Check engine light illuminates
  • OBD trouble code P2404 and/or P0441 is stored
  • Engine will not start after refueling (must crank for over 30 seconds)
  • Vibration when slowing to a stop

The cause is a valve which is mounted on the front of the intake manifold, commonly called the N80 valve, or EVAP system purge valve. The valve is designed to open under specific circumstances, but a worn valve will remain open at all times, preventing the pressurization of the fuel tank. 

Correction of the issue is to replace the N80 valve with the latest revision. 

The Check Engine Light may illuminate with a knock sensor code stored. Our technicians tell us a revised knock sensor and bracket should be installed, along with heat shielding material to protect the new sensor, to correct this condition.

The anti-lock brake system (ABS) control module may fail causing the ABS light to illuminate. Failed modules should be replaced to restore ABS operation.

A problem with the torque converter can cause the Check Engine Light to illuminate.

The Audi A4 2.0T FSI engine looses power if the turbocharging system has a leak. The most common turbo boost leak is a torn rubber diaphragm on the diverter valve, which is intended to open only if pressure gets too high. Common symptoms are increased turbo noise when letting off of the gas pedal, power loss, and engine code P0234.

If there is a turbocharging system leak, the system will need to be inspected, and the defective seals and/or valve will require replacement. 

The thermostat may erratically stick open or closed. The can result in illumination of the Check Engine Light and/or engine overheating.

The anti-lock brake system (ABS) control module may fail causing the ABS light to illuminate. Failed modules should be replaced to restore ABS operation.

The 2007-2017 Audi A8 with FSI/TFSI, including the W12 are direct injection engines. These engines are subject to carbon buildup in the intake system which can cause power loss, OBD codes and a check engine light, and a rough idle. In normal engines, the engine is cleaned by the gasoline flowing through the injectors and into the intake system, however, the A8 uses direct injection so gasoline does not flow through common carbon buildup areas. 

Possible trouble codes include: P0300P0301P0302P0303P0304, P0305, P0306, P0307, P0308, P0309, P0310, P0311, P0312.

The solution is to remove the intake manifold and professionally clean the intake manifold, intake ports on the cylinder head, and the intake valves. This may need to be done in as few as 20,000 miles. 

The 2006-2016 Audi A6 2.0TFSI, 3.0TFSI, 3.2FSI and 4.2FSI direct injection engines are subject to carbon buildup in the intake system which can cause power loss, OBD codes and a check engine light, and a rough idle. In normal engines, the engine is cleaned by the gasoline flowing through the injectors and into the intake system, however, the A6 uses direct injection so gasoline does not flow through common carbon buildup areas. 

Possible trouble codes include: P0300P0301P0302P0303P0304, P0305, P0306, P0307, P0308

The solution is to remove the intake manifold and professionally clean the intake manifold, intake ports on the cylinder head, and the intake valves. This may need to be done in as few as 20,000 miles. 

The 2007-2016 Audi S6 4.0TFSI and 4.2FSI direct injection engines are subject to carbon buildup in the intake system which can cause power loss, OBD codes and a check engine light, and a rough idle. In normal engines, the engine is cleaned by the gasoline flowing through the injectors and into the intake system, however, the S6 uses direct injection so gasoline does not flow through common carbon buildup areas. 

Possible trouble codes include: P0300P0301P0302P0303P0304, P0305, P0306, P0307, P0308

The solution is to remove the intake manifold and professionally clean the intake manifold, intake ports on the cylinder head, and the intake valves. This may need to be done in as few as 20,000 miles. 

The 2007-2016 Audi S8 4.0TFSI and 5.2FSI direct injection engines are subject to carbon buildup in the intake system which can cause power loss, OBD codes and a check engine light, and a rough idle. In normal engines, the engine is cleaned by the gasoline flowing through the injectors and into the intake system, however, the S8 uses direct injection so gasoline does not flow through common carbon buildup areas. 

Possible trouble codes include: P0300P0301P0302P0303P0304, P0305, P0306, P0307, P0308, P0309, P0310.

The solution is to remove the intake manifold and professionally clean the intake manifold, intake ports on the cylinder head, and the intake valves. This may need to be done in as few as 20,000 miles. 

The 2006 - 2017 Audi A3 2.0FSI, 2.0TFSI, and 3.2FSI direct injection engines are subject to carbon buildup in the intake system which can cause power loss, OBD codes and a check engine light, and a rough idle. In normal engines, the engine is cleaned by the gasoline flowing through the injectors and into the intake system, however, the A3 uses direct injection so gasoline does not flow through common carbon buildup areas. 

Possible trouble codes include: P0300P0301P0302P0303P0304, P0305, P0306.

The solution is to remove the intake manifold and professionally clean the intake manifold, intake ports on the cylinder head, and the intake valves. This may need to be done in as few as 20,000 miles.