» » »

Problems for specific Mercedes-Benz S500 years:

Car problem reports

Report A Problem

Problem with your car? See what our experts say or submit your own.

Newest reported 1996 Mercedes-Benz S500 problems

 

Verified for the Mercedes-Benz S500

The evaporator temperature sensor can fail, causing the AC compressor not to cycle. If the AC compressor does not turn on, the AC system will not blow cold air. If the compressor is stuck on, the air will be very cold at first, before warming up.

12 Reports
Me Too

Verified for the Mercedes-Benz S500

A faulty mass air flow (MAF) sensor can cause erratic/rough engine operation and fuel economy issues. Since this sensor measures the actual amount of air entering the motor, when it fails, the engine control module (ECM) takes the wrong information and delivers incorrect volumes of fuel to the cylinders.

9 Reports
Me Too

Verified for the Mercedes-Benz S500

Ports in the cylinder head related to the emissions air injection and EGR systems can clog; the cylinder head should be removed and the ports cleaned.

6 Reports
Me Too

Verified for the Mercedes-Benz S500

A refrigerant leak may develop from one or more of the following AC components: AC compressor, hose manifold for the compressor, or the evaporator core. The loss of refrigerant can cause poor AC performance. Our technicians tell us that proper leak diagnoses should be performed in order to determine the cause of any refrigerant loss.

7 Reports
Me Too

Verified for the Mercedes-Benz S500

The crankshaft position sensor may fail. Symptoms of this are: The engine will crank—but not start—especially when the engine is warm. The car may start again if it is left to cool off, but it may run roughly or have poor performance.

18 Reports
Me Too

Verified for the Mercedes-Benz S500

Other than a defective motor, a bad switch or blower motor resistor assembly can cause an inoperative heater blower motor.

7 Reports
Me Too

Verified for the Mercedes-Benz S500

The lower control arm bushings can wear and crack, resulting excessive movement at the control arm pivot point, leading to irregular and premature tire wear. Worn Ball joints can also cause similar tire wear symptoms. I some cases it may be necessary to replace the lower control arm, including bushings & ball joint to correct this concern.

6 Reports
Me Too

Verified for the Mercedes-Benz S500

The head lamp wipers are easily damaged, especially by automatic car washes.

7 Reports
Me Too

Verified for the Mercedes-Benz S500

Due to exposure to the sun, lenses for head lights may become opaque (cloudy or hazy). This reduces the effectiveness of the lights. Our technicians tell us plastic polishes can improve the clarity of the lenses, but replacement of the lamp housings is the only way to regain the full intensity of the lights.

8 Reports
Me Too

Verified for the Mercedes-Benz S500

The cooling system hoses may fail unexpectedly. The hoses can look good on the outside, but the rubber can degrade and erode on the inside. If not carefully checked, the hoses can burst at any time.

7 Reports
Me Too

Verified for the Mercedes-Benz S500

The climate control system can fail or perform erratically due to internal problems with the climate control button electrical contacts. Replacement of the climate control assembly is commonly required to correct this problem.

9 Reports
Me Too

Verified for the Mercedes-Benz S500

Vehicles with automatic level control that ride harshly in the rear (no give in the suspension) may have one or both dampening actuators which have failed. It is commonly recommended the actuators be replaced in pairs.

9 Reports
Me Too

Verified for the Mercedes-Benz S500

The electronic throttle assembly may suffer an electrical failure. It is often cheaper to send the valve to a service center for repair that to purchase a new part.

6 Reports
Me Too

Verified for the Mercedes-Benz S500

Problems with the pneumatic system can cause closing assist and door lock issues.

21 Reports
Me Too

Verified for the Mercedes-Benz S500

A coolant leak may develop form the Radiator due to degradation of its plastic components. Replacement of the failed radiator will be necessary.

6 Reports
Me Too
Ask a Question