» » »

Problems for specific Jeep Grand Cherokee years:

Car problem reports

Report A Problem

Problem with your car? See what our experts say or submit your own.

Repairpal verified 1995 Jeep Grand Cherokee problems

 

Verified for the Jeep Grand Cherokee

If the downstream (rear) oxygen sensor wiring harness contacts the propeller (drive) shaft, it can damage the oxygen sensor and the wiring harness for the sensor, and/or cause Check Engine Light illumination. The wiring harness should be repaired and secured away from propeller shaft.

1 Report
Me Too

Verified for the Jeep Grand Cherokee

When normal alignment practices do not bring components into the alignment specifications, offset upper ball joints are available.

5 Reports
Me Too

Verified for the Jeep Grand Cherokee

If a thumping or creaking noise is heard from the transmission tunnel area while driving over bumpy roads, a transfer case shifter repair kit is available which should correct this concern.

6 Reports
Me Too

Verified for the Jeep Grand Cherokee

The AC/heater (HVAC) system may unexpectedly switch to the defrost mode when accelerating. This system is operated by engine vacuum and should be inspected for any vacuum leaks if this problem develops.  There is also a revised vacuum check valve available to address this concern.

37 Reports
Me Too

Verified for the Jeep Grand Cherokee

A ticking type noise may be noted from the engine area due to an exhaust manifold that has cracked where the pipes are welded; cracked manifolds should be replaced.

13 Reports
Me Too

Verified for the Jeep Grand Cherokee

A no crank or no start condition may develop due to electronic lockup of the wireless control module (WCM), also referred to as the Sentry Key Remote Entry Module (SKREEM). When this module fails the remote keyless entry system will also not operate. The WCM is commonly replaced to correct this concern.

17 Reports
Me Too

Verified for the Jeep Grand Cherokee

On the 3.9L V6 and 5.9L V8 the engine oil leaks at the distributor can be misdiagnosed as leaks from the intake manifold seal, oil pan gasket, or rear crankshaft (rear main) seal. A revised distributor is available if oil is found inside the distributor.

4 Reports
Me Too

Verified for the Jeep Grand Cherokee

If the oil filter casing shows signs of distortion from excessive oil pressure, the oil pump should be replaced.

3 Reports
Me Too

Verified for the Jeep Grand Cherokee

External oil leaks from the valve cover gaskets, intake manifold gaskets (front or rear), and the rear crankshaft seal area are common. The rear main seal is an unlikely source. Normally, leaks in this area are from the bearing cap mating surfaces as well as the sealing surface between the oil pan and bearing cap.

8 Reports
Me Too

Verified for the Jeep Grand Cherokee

On 3.9L V6 and 5.9L V8 engines, the intake manifold gasket may leak and cause increased oil consumption and a spark knock during acceleration; the gasket should be replaced.

9 Reports
Me Too

Verified for the Jeep Grand Cherokee

Leaks at the front and/or rear differential pinion seal and from the transfer case are common. Leakage from the transfer case normally occurs at the case-mating surfaces and require removal of the transfer case to reseal.

53 Reports
Me Too

Verified for the Jeep Grand Cherokee

Loose or worn suspension and steering components can cause a wobble or shaking in the steering wheel. It may happen at a certain speed and subside as the vehicle accelerates through the range. Tire balance can contribute to this as well.

38 Reports
Me Too

Verified for the Jeep Grand Cherokee

The AC evaporator drain commonly clogs and causes water to leak onto the passenger side floor. A sloshing noise may also be heard from the water inside the heater housing. Decaying organic debris in the housing may cause an odor. A service bulletin (TSB 24-06-96) was released; it describes how to clean the drain tube without removing the heater AC housing.

21 Reports
Me Too

Verified for the Jeep Grand Cherokee

Due to warped front brake rotors or variations in the thickness of the rotors, brake pulsations may develop. The best method to reduce pulsations is to use an "On the Car" brake lathe (as long as the rotors are suitable for turning). "On the Car" equipment can correct variations (or "runout") in the rotor surfaces because it also corrects variations in other components (e.g. the hub).

69 Reports
Me Too

Verified for the Jeep Grand Cherokee
Internal leaks in the speed sensor or speed sensor gear adapter (speedometer adapter) are common. A revised speed sensor (white in color, old versions are black), used in production since November of 1993, solves the problem. If leaks develop between the sensor and the adapter or between the adapter and the transmission housing (transfer case if 4WD), a revised speedometer adapter is available.
2 Reports
Me Too
Ask a Question