The spark plugs may become dislodged from the cylinder heads. A loud popping noise can be heard and a subsequent misfire experienced. The threads on the spark plug ports in the cylinder head(s) can become stripped or missing when the spark plug is dislodged. The threads in cylinder heads may be replaced using “Lock-N-Stitch” aluminum inserts. Our technicians tell us thread replacement is performed when the vehicle is out of base warranty. Vehicles under base warranty receive a new cylinder head.
2005 Ford E-350 Problem Reports
Newest 2005 Ford E-350 Problem Reports
The Check Engine Light may illuminate, the engine may run rough and have misfires on acceleration. Commonly the ignition coils and/or the ignition coil boots are the cause of this problem. The rubber boot that insulates the coil to the spark plug can dry and crack allowing arcing. Inspect the coils and boots, and replace them as needed. Our technicians also recommend replacing the coil boots any time the spark plugs are replaced.
The front end may make a rattle noise over bumps. There may be handling issues, and play in the front wheels on inspection. If there is up and down movement on the front wheels while the lower control arms are being supported, inspect the upper and lower ball joints for excessive play. These are prone to failure from moisture entry and lack of lubrication. The ball joints should be replaced as needed.
If the slip yoke in the driveshaft is binding, it can make a clunking noise when pulling away from a stop. The slip yoke will need to be lubricated.
The engine may stall and not restart. There is a recall to replace the camshaft position sensor, found to be defective. Replace the camshaft position sensor if that is found to be the problem.
Delamination of the diesel fuel tank can occur resulting in a loss of power due to debris clogging the fuel filters. In some cases the fuel injection pump and/or fuel injectors have also been damaged. Ford has issued a service bulletin (#
my van starts up great but after driving it for awhile it just dies giving no warning or code. i have changed the fuel pump and have changed the ecm and it runned great for a month then hey same problem occured again. i have notice oil leaks from my oil sending unit and head gasket both sides and am stilling having the problem and ooh it takes ahwile to start up after it shuts off, can anyone help with any suggestions.
Electrolysis can cause repeated failures of the heater core and radiator. The diagnosing technician should check for voltage present in the coolant, with the battery disconnected, because electrical current in the coolant causes electrolysis. Corroded or deteriorated parts should be replaced, and the coolant should be flushed. Ground straps can be added to help prevent future corrosion of components.
Leaking exhaust manifold gaskets can cause exhaust fumes to enter the vehicle. The exhaust manifold gaskets should be replaced as needed.
Broken pieces from catalytic converter can travel to the muffler and rattle, causing a buzzing noise to be heard in the muffler or exhaust system. The exhaust catalytic converter and muffler/pipe assemblies should be replaced.
A lack of power and possible Check Engine Light may be experienced with codes P0238, P0299, P0404, P0478, P2262, P2263. The turbocharger can become internally contaminated with sludge and deposits causing the variable vanes within the turbo to seize. The turbocharger can be disassembled to be cleaned, and the internal parts can be replaced as needed. If deterioration is too bad, replacement of the turbocharger may be necessary.
If the vehicle hesitates on acceleration, idle is low, and the Check Engine Light may be on, this condition can be caused by contaminated throttle body. Diagnosis is needed but the throttle body should be inspected and replaced if needed, and the engine's computer programming should be updated.
Internal issues with the Fuel Injector Control Module (FICM) can cause the engine to run rough, lack power, not start, or it may be hard to start. The FICM should be inspected for proper software revision and internal function. To repair, update the software, replace internal parts, and / or replace the entire FICM as needed.
A casting issue with the cylinder heads may allow fuel leakage into the cooling system. The cylinder heads should be inspected for fuel leakage where the injectors mount. Replacement of the cylinder head(s) that leak will be needed.
The Check Engine Light may come on with codes in engine computer memory for P0401, P0402, P0404, and P1335. In addition white or black smoke will be emitted from the tailpipe and the engine will feel down on power. This is most commonly caused by build up of black sludge and other solid deposits in the Exhaust Gas Recirculation (EGR) System (EGR Valve, EGR Cooler, Exhaust Back Pressure (EBP) Sensor, and EBP tube), intake manifold, turbocharger and the EGR throttle plate. Regularly adding a cetane booster to the fuel will aid in a more complete combustion and the engine oil should be replaced at the proper intervals to avoid sludge build up. Installing an EGR baffle kit also helps to prevent future EGR valve contamination.