Problem Reports
Problem with your car? See what our experts say or submit your own.
2001 Chrysler Concorde Problems
Noise in Front Suspension Due to Worn Sway Bar Bushings/End Links
Worn sway bar bushings or sway bar end links may cause a rattling or clunking noise from the front suspension during low-speed driving. Though not always the root cause, front struts are often replaced for this condition.
The Window Glass May not Roll Correctly Due to Damaged Glass Lift Plates
The window glass lift plates tend to bend or break and cause the window glass to tilt and bind in the door. The lift plates can be replaced separately from the window regulator. In more severe cases, however, a new window regulator may also require replacement.
Odor from HVAC vents
Some vehicles may develop a musty odor coming from the HVAC system, Dodge has issued a cleaner/disinfectant and a coating for the evaporator designed to inhibit bacterial growth.
Stalling or Low Engine Idle Speed Due to Dirty Throttle Body
A dirty throttle body may cause low engine idle speed or frequent stalling, as oily residue blocks air flow in the throttle when the throttle is closed. Throttle body cleaning may be necessary to correct this condition. Our technicians caution against spraying cleaner directly onto the throttle body as this may damage the throttle position sensor (TPS).
Engine Does Not Start and PCM Fault Code Stored
When a no start condition is caused by a faulty camshaft or crankshaft sensor, related fault codes stored in the powertrain control module (PCM) should not be trusted. Our technicians tell us that under certain conditions a fault code can be stored for the "good" sensor. Care should be taken to properly diagnose this condition.
Poor Heat Output and/or Engine Overheating
Poor output from the heater and/or engine overheating can be caused by air left in the cooling system after the cooling system has been serviced. Our technicians tell us the proper coolant fill procedure should be used to prevent this problem from occurring.
Wind Noise and/or Water Leak Due to Weatherstrip Issue
Door weatherstrips mounted on the body tend to shrink with age, leaving gaps that can create wind noise or allow water to leak into the car. Our technicians suggest the door weatherstrips should be replaced to correct these issues.
Ignition Key Will not Turn or Cannot be Removed From Lock Cylinder
If the ignition key does not turn and/or cannot be removed, a new lock cylinder may be needed. A worn key can also cause similar problems.
Damaged Cam Position Sensor May Cause Engine Problems
A damaged cam position sensor (or its wires and connector) can cause intermittent stalling, stumbles, or hard starting.
Growling Noise From Engine at Low Speeds
An loose alternator drive belt may cause a growling noise in the engine area at low speeds (usually when accelerating from a stop). This is often mistaken for catalytic converter failure.
Make Sure Air Bleed Valve is Open Before Refilling Coolant
Before refilling the coolant, make sure the air bleed valve is open. Follow the proper fill procedure—it will prevent problems with overheating, low heat output from the heater, and possible coolant bottle failure.
Ticking Sound After Cold Start Due to Worn Exhaust Rocker Arm Swivel Pads
A ticking sound (lasting only two to three seconds) may be heard when starting a cold engine. Worn swivel pads on the exhaust rocker arms are commonly the cause. Worn swivel pads will require replacement.
Replacement pieces available if exterior side view mirror glass breaks
Airbag light On Due to Damaged or Dirty Connectors Under the Seat
On vehicles equipped with side airbags, placing articles under the seat can damage wiring. Loose, damaged, or dirty connectors under the seat are frequent causes for intermittent airbag lamp illumination.
Update to BCM Will Fix Problems With Instrument Cluster/Fuel Gauge
The instrument cluster may illuminate randomly to its full brightness and/or the fuel gauge may drop to the empty position. Typically the symptoms are infrequent and the instrument cluster returns to normal operation after a few seconds. An update to the body control module (BCM) will fix this problem.
-
Verified
Quality Work -
Guaranteed
Fair Prices -
Happy
Customers